Bedienungsanleitung Powerplus POWX1425 (Seite 7 von 12) (Englisch)

645074

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

POWX1425 EN

 When you want to restart a saw that is stuck in a workpiece, center the saw blade in the

saw gap and check that the saw teeth are not stuck in the workpiece. If the saw blade

jams, it can move out from the workpiece or a kickback can happen if the saw is restarted.

 Prop up large panels in order to minimise the risk of a kickback by a jammed saw blade.

Large panels tend to sag under their own weight. Panels must be supported on both sides,

both in the vicinity of the saw gap as well as on the edge.

 Do not use dull or damaged saw blades. Saw blades with blunt or misaligned teeth cause

increased friction, jamming of the saw blade and kickback by an excessively narrow saw

gap.

 Tighten the cutting depth position prior to cutting. If the settings change while cutting, the

saw blade can jam and a kickback can occur.

 Be especially careful if you perform a "circular cut" in a hidden area, such as an existing

wall. The protruding saw blade can get blocked in hidden objects while cutting and cause

a kickback.

 Do not place the saw on the workbench or the floor unless the saw blade is at a standstill.

An unprotected, running saw blade moves the saw against the cutting direction and cuts

whatever is in its way. Thus note the delay time of the saw.

 For this reason, the saw is not suitable for use in reverse position as fixed equipment.

 Do not operate the saw if it is not working properly or has been damaged. In case of

technical problems, do not attempt to repair it on your own. Contact the service or have

the saw repaired by a professional.

8 ASSEMBLY

Check for damage to the tool, parts and accessories which may have occurred during

transportation. Take some time to read this manual carefully and understand all the content

prior to assembly and operation.

CAUTION! Always ensure that the tool is switched off and unplugged from

the mains supply before assembly.

8.1 Changing the blade (Fig. 1, 2, 3)

 Place the saw on its side of a flat surface.

 Put the hex key in the hex bolts head. While keeping the Spindle Lock Button(11)

depressed, turn the hex key (F) slowly clock-wise until the blade locks ( spindle lock

latches into place) and continue turning it to loosen the blade clamp screw(8).

 Remove the blade clamp screw(8), the washer and the outer flange.

 Press the unlock button (5) , hold, lift the base plate (pushing the front side upward) to free

the blade and remove it.

 Clean the saw blade flanges and then mount the new saw blade onto the spindle.

 Make sure the saw teeth and arrow on the blade point in the same direction as the arrow

shown on the guard.

 Reinstall the outer flange, washer and tighten the blade clamp screw(8) anti-clockwise.

 Make sure the saw blade can turn freely by turning the blade using the hex key. (check the

spindle-lock button is unlocked).

8.2 Parallel cut adjustment.( See Fig 4)

 Loosen the edge guide locking screw(1).

 Slide the edge guide through the slots (13) in the slot to the desired width.

 Tighten the edge guide locking screw(1) to secure it in the position.

 Ensure that the fence guide(E) rests against the wood along its entire length to give a

consistent parallel cuts.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX1425 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX1425

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info