Bedienungsanleitung Powerplus POWX1425 (Seite 8 von 12) (Englisch)

645074

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

POWX1425 EN

8.3 Dust extraction (Fig. 5)

The circular saw is a powerful tool capable of producing a large amount of dust. As the tool

has a fully enclosed blade, forced dust extraction is particularly efficient. Forced dust

extraction should be used for all but small trimming jobs.

 Push the dust extraction hose (b) on to the dust extraction nozzle (12).

 Connect a vacuum device approved for the extraction of sawdust and splinters to the dust

extraction hose (b).

9 OPERATION

9.1 Switching on and off (Fig. 6)

Note: Before engaging the on/off switch, check the saw blade to see if it is

fitted properly and runs smoothly, and the blade clamp screw is well

tightened.

 Connect the plug to the power supply.

 To start the tool, depress the unlock button(5) and press the switch trigger(6).

 Release the trigger(6) to turn the tool off.

9.2 Line following (Fig. 7)

A V-shaped pointer and pointer locate at the front and the rear position of the base plate (14)

which allow a line to be followed, when cutting.

9.3 Depth Adjustment (Fig.8)

 Loosen the cutting depth setting clamp(7) by lifting the lock lever.

 Hold the base plate flat against the work piece, press the unlock button(5) and lift the

plunge saw body gradually until the blade reaches the right depth.

 Tighten the depth locking lever of the cutting depth setting clamp(7).

Note: for best cutting results, always check the cutting depth before every

cutting. In order to protrude completely, the thickness of the work piece

can not be thicker than 28.5mm.

9.4 General cut

 Check the specifications to ensure the suitability of the material to be cut.

 Fit the correct blade ensuring it is sharp and not damaged.

 Set the depth of cut.

 Mount and connect the dust collection system.

 Place the material to be cut onto a flat surface such as a workbench, table or floor. Use a

piece of scrap material underneath if: You do not wish to damage the work surface.

 Plug into mains supply.

 Grasp the tool firmly and rest its metal base plate onto the surface to be cut. Ensure that

the rear half of the base plate overhangs the work surface. Do not plunge the blade into

the material.

 Switch on the tool and wait for a moment for the blade to run up to speed. Next, depress

the unlock button (5) and plunge the blade into the material slowly and gently, but firmly.

Then push the tool forwards along the line to be cut.

 NOTE: Never draw the tool backwards.

 Very little force should be used to feed the tool along the cut. Excess force will cause

operator fatigue and excessive wear to the blade and tool. Excess force is also likely to

cause the temperature cut-out to trip, resulting in delays.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWX1425 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWX1425

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info