Bedienungsanleitung Powerplus POWXG1006 (Seite 9 von 14) (Englisch)

517142

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

POWXG1006 EN

9.7 Chain lubricants

The service life of saw chains and guide bars depends to a large extent on the quality of the

lubricant used. Old oil must not be used! Use only environment-friendly chain lubricant. Store

chain lubricant only in containers which comply with the regulations.

9.8 Guide bar

The guide bar (7) is subjected to especially severe wear and tear at the nose and the bottom.

To avoid one-sided wear and tear, turn the guide bar over every time when you sharpen the

chain.

9.9 Chain wheel

The chain wheel (16) is subjected to especially high wear and tear. If you notice deep wear

marks on the teeth, the chain wheel must be replaced. A worn chain wheel curtails the service

life of the saw chain. Have the chain wheel replaced by a specialist dealer or your Customer

Service.

9.10 Chain guard

The chain guard must be clipped onto the chain and sword as soon as the sawing work has

been completed and whenever the chainsaw has to be transported.

9.11 Chain brake

In the event of kick-back, the chain brake (3) will be actuated via the front finger guard. The

front finger guard is pushed forwards by the back of the hand and this causes the chain brake

to stop the chain saw, or rather the motor, within 0.15 s (Fig 5, I).

9.12 Releasing the chain brake (Fig 5)

To be able to use your chain saw again, you must release the saw chain again. First switch off

the chainsaw. Then push the front finger guard (3) back into the vertical position until it locks in

place (Fig 5, H). The chain brake is now fully functional again.

9.13 Sharpening the saw chain

You can have your saw chain sharpened fast and correctly by specialist dealers, from whom

you can also obtain chain sharpening equipment to enable you to sharpen the chain yourself.

Please follow the corresponding operating instructions.

Take care of your tools. Keep your tools sharp and clean to enable you to work well and safely.

Follow the maintenance regulations and the instructions for changing tools

10 STARTING UP

Always wear safety goggles, ear muffs, protective gloves and heavy-duty

work clothes!

Use the saw only with approved extension cables with the prescribed insulation and

connections designed for outdoor use (approved rubber-sheathed cables) which fit the

chainsaw plug.

The chain saw is equipped with two safety switches, requiring the use of both hand

The chainsaw works only when one hand holds the front grip (2) and the other hand actuates

the switch on the rear grip (1).

If the chainsaw does not run, the chain brake must be released at the front finger guard (3). Be

sure to read the sections “Chain brake” and “ Releasing the chain brake “ on this point.

After switching on, the chainsaw will run immediately at high speed .

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWXG1006 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWXG1006

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info