Bedienungsanleitung Powerplus POWXG1006 (Seite 10 von 14) (Englisch)

517142

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

POWXG1006 EN

10.1 To switch off

Release either the ON/OFF switch (13) on the rear grip or the other switch (2) on the front grip.

The release of ON/OFF switch results the stop of the chainsaw within 1sec., and heavy

sparkling. This is normal and safe for the proper operation of the chainsaw.

After working with the chainsaw, you should always: Clean the saw chain and guide bar and

replace the chain guard.

10.2 Chainsaw protection

Never use the chainsaw in the rain or in damp conditions.

If the extension cable is damaged, pull the plug out of the power socket

immediately. Never work with a damaged cable.

 Check the chainsaw for damage. Before using your tool again, check the safety devices or

any slightly damaged parts to ensure that they are in good working order.

 Make sure the moving parts are working correctly.

 All the parts must be correctly assembled and meet all the conditions required to ensure

that the chainsaw works correctly.

 Any damaged safety devices and parts must be properly repaired or replaced immediately

by a Customer Service workshop, unless there are instructions to the contrary in these

operating instructions.

10.3 Notes on working practice

Kick-back (Fig 8)

You can avoid accidents by not sawing with the tip of the guide bar as this may cause the saw

to rear up suddenly.

Always use the complete safety equipment and clothes when working with the saw.

Kick-back is an upward and/or backward movement of the guide bar which can occur if the

saw chain at the tip of the guide bar encounters an obstruction.

Make sure your work-piece is firmly secured. Use clamps to stop the work-piece slipping. This

also makes it easier to operate the chainsaw with both hands.

Kick-back causes the saw to behave uncontrollably and thus brings with a slack or blunt chain.

A poorly sharpened chain increases the risk of kick-back. Never saw above shoulder height.

11 OPERATION - TIPS ON CHAIN SAW USE

11.1 Sawing up wood (Fig 7a, 7b)

To saw up wood, please observe the safety regulations and proceed as follows:

 Make sure the wood to be sawed cannot slip.

 Clamp short pieces of wood in place before sawing

 Saw only wood or wooden objects.

 When sawing, make sure that no stones or nails are touched as these could be thrown out

and damage the saw chain.

 Avoid bringing the running saw into contact with wire fences or the ground.

 When lopping off branches, support the chainsaw as far as possible and do not saw with

the tip of the guide bar.

 Watch out for obstacles such as tree stumps, roots, ditches and hillocks as these could

cause you to fall.

Remember!

The chain saw must be running before it comes into contact with the wood.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWXG1006 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWXG1006

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info