Bedienungsanleitung Powerplus POWXG2061 (Seite 7 von 16) (Englisch)

582051

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

POWXG2061 EN

 See instructions under the heading Start. Start the machine and apply full throttle. Release

the throttle and check that the cutting attachment stops and remains at a standstill. If the

cutting attachment rotates with the throttle in the idle position then the carburetor idle

setting must be checked. (Fig. 4)

8.2 Engine switch (Fig. 5)

Press down the “O” side of the engine switch to stop the engine.

Start the engine and make sure the engine stops when you move the engine switch to the stop

setting.

8.3 Vibration damping system (Fig. 6)

Your machine is equipped with a vibration damping system that is designed to minimize

vibration and make operation easier.

Using incorrectly wound cord or a blunt or incorrect cutting attachment (wrong type or

incorrectly filed, see instructions under the heading Filing the blade) increases the level of

vibration.

The machine′s vibration damping system reduces the transfer of vibration between the engine

unit/cutting equipment and the machine′s handle unit.

Regularly check the vibration damping units for cracks or deformation.

Check that the vibration damping element is undamaged and securely attached.

8.4 Quick release

There is an easily accessible, quick release fitted near the suspension ring as a safety

precaution in case the engine catches fire, or in any other situation that requires you to free

yourself from the machine.

8.5 Muffler

The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away

from the user.

Never use a machine that has a faulty muffler.

Regularly check that the muffler is securely attached to the machine.

The inside of the muffler contain chemicals that may be carcinogenic. Avoid

contact with these elements in the event of a damaged muffler.

Bear in mind that: The exhaust fumes from the engine are hot and may

contain sparks which can start a fire. Never start the machine indoors or

near combustible material!

9 CUTTING EQUIPMENT (FIG. 7)

To ensure good cutting results it is important that the contact pressure between the blades is

correct. The contact pressure is adjusted by turning the screws on the underside of the bar

clockwise as far as they will go. Then turn the screws anticlockwise a 1/4 turn. Lock the

screws using the locking nut on the top of the bar. Check that the screws are loose enough to

allow the washers under the screw heads to slide sideways.

When the blades are correctly adjusted the play between the blades should be 0,2–0,4 mm,

measured at the screws.

The edges of the blades are too hard to be filed. Dull blades should be sharpened using a

grinder.

Replace the blades if they are bent or damaged.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWXG2061 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWXG2061

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info