Bedienungsanleitung Powerplus POWXG3025 (Seite 9 von 20) (Englisch)

582100

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

POWXG3025 EN

Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the

correct length.

To increase the life of the cord it can be soaked in water for a couple of days. This will make

the line tougher so that it lasts longer.

10 CUTTING EQUIPMENT (LONG REACH HEDGE TRIMMER)

To ensure good cutting results it is important that the contact pressure between the blades is

correct. The contact pressure is adjusted by turning the screws on the underside of the bar

clockwise as far as they will go. Then turn the screws anticlockwise a 1/4 turn. Lock the

screws using the locking nut on the top of the bar. Check that the screws are loose enough to

allow the washers under the screw heads to slide sideways.

When the blades are correctly adjusted the play between the blades should be 0,2–0,4 mm,

measured at the screws.

The edges of the blades are too hard to be filed. Dull blades should be sharpened using a

grinder.

Replace the blades if they are bent or damaged.

11 OPERATING INSTRUCTIONS

11.1 Prepare the machine

11.1.1 Assembling the Front handle

Fit the front handle absorber (A) on the rear tube (C). While aligning the hole (B) on the front

handle absorber、the position pin (F) on the barrier (E) and one position hole (D) of three on

the rear handle, fit the barrier on the rear handle and insert the position pin into the position

hole on the rear handle. Make sure the barrier on the left side of the machine. (Fig. 10)

Push down the front handle (G), and then turn four screws (H) clockwise to tighten the front

handle securely. (Fig. 11)

11.1.2 Connecting the tube (Fig. 12)

Align the hole (A1) on the front tube (A) and the lock pin (B). Then, Pull out the Lock pin, and

while inserting the front tube in the connector (D) to the end. After loosened the lock pin, it will

return to its original position automatically, and insert into the hole on the front tube.

Make sure the front tube can’t be rotated after the lock pin came back to its original position.

Turn the lock knob (C) clockwise to tighten the front tube securely.

11.1.3 Fitting blades and trimmer heads

When fitting the cutting attachment it is extremely important that the raised

section on the top clamping plate/support flange engages correctly in the

centre hole of the cutting attachment. If the cutting attachment is fitted

incorrectly it can result in serious and/or fatal personal injury.

Never use a cutting attachment without an approved guard. See the chapter

on Technical data. If an incorrect or faulty guard is fitted this can cause

serious personal injury.

11.1.4 Fitting the guard extension

 The guard extension shall always be fitted when using the trimmer head and combination

guard. The guard extension shall always be removed when using the grass blade. (Fig.

13)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWXG3025 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWXG3025

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info