Bedienungsanleitung Powerplus POWXG3025 (Seite 10 von 20) (Englisch)

582100

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

POWXG3025 EN

 Hook the blade guard/combination guard onto the fitting on the shaft and secure with three

bolts. (Fig. 13)

 Enter the guard extension guide in the slot of the combination guard. Then click the guard

extension into position on the guard with some claws. (Fig. 14)

 The guard extension is removed easily using a screwdriver, see illustration. (Fig. 15)

11.1.5 Fitting a blade guard, grass blade and grass cutter

 Hook the blade guard/combination guard onto the fitting on the shaft and secure with three

bolts. Use the recommended blade guard. See the Technical data section. (Fig. 16)

CAUTION! Ensure that the guard extension is removed.

 Fit the top clamping plate (B) on the output shaft.

 Turn the blade shaft until one of the holes in the top clamping plate aligns with the

corresponding hole in the top protecting cap.

 Insert the locking pin (A) in the hole to lock the shaft.

 Place the blade (C), bottom clamping plate (D) and bottom protecting cap (E) on the

output shaft. (Fig. 17)

 Fit the nut (F). The nut must be tightened to a torque of 35-50 Nm. Use the socket

spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as

possible. To tighten the nut, turn the spanner in the opposite direction to the direction of

rotation (Caution! left-hand thread).

 Pull out the locking pin after all installation process has been finished.

11.1.6 Fitting the trimmer guard and trimmer head (Fig. 18)

 Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with

three bolts.

 Fit the top clamping plate (B) on the output shaft.

 Turn the blade shaft until one of the holes in the top clamping plate aligns with the

corresponding hole in the top protecting cap (C).

 Insert the locking pin (A) in the hole to lock the shaft.

 Screw on the trimmer head (D) in the opposite direction to the direction of rotation.

 To dismantle, follow the instructions in the reverse order.

11.1.7 Fitting cutting head (Hedge trimmer) (Fig. 19)

Fit the cutting head (B) on the shaft tube (A) so that the screw hole on the cutting head is

aligned with the position hole (A1) on the shaft tube as shown. Then, tighten the lock screw (D)

and the position screw (C) securely.

Changing the hedge trimmer angle

Press the safety lever (E). Then press the lock lever (F), at the same time hold the grip (G)

and turn the cutting head to a desired angle (α).

11.1.8 Adjusting the harness (Fig. 20)

WARNING! When using the machine it must always be hooked securely to

the harness. Otherwise you will be unable to control the brush cutter safely

and this can result in injury to yourself or others. Never use a harness with

a defective quick release.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Powerplus POWXG3025 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Powerplus POWXG3025

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info