725417
10
Zoom out
Zoom in
Vorherige Seite
1/14
Nächste Seite
POWXG6462 EN
Copyright © 2020 VARO P a g e | 10 www.varo.com
9.2 Freeing up a jam
9.2.1 Overload protection switch (11) motivated
Press the function switch (8) to return to neutral position. (Fig. 4)
After 1-2 minutes, press down the overload protection switch (11) to repower the machine.
Press the function switch (8) upwards to allow the blade rotate anti-clockwise to return the
material.
Press the "ON" switch (9) to start the machine to return the jammed material.
Switch the shredder ON and OFF (see" switching the shredder on and off ) to check if the
jam is fixed.
If jam is fixed, switch the shredder ON (see" switching the shredder on and off ) to
continue shredding material.
If jam is not fixed, repeat above steps. If still fail to fix (Fig. 5), open the blade cover (22) to
clean the jammed material.
a. Unplug the power supply.
b. Loosen the four blade cover screws (21) by enclosed Allen key.
c. Pull to remove the blade cover (22).
d. Clean the jammed material from the cylinder blade (23) and pressure plate (24).
e. Put the blade cover (22) back and tighten the four screws (21).
Connect the power supply and switch the shredder ON and OFF to check.
9.3 Adjusting the pressure plate
The pressure plate factory setting is correct and only has to be adjusted when worn. You will
recognize that the cutting system has become worn when the shredded material is only
compressed, and comes out in long chains.
The running-in process may require that you initially readjust the pressure plate (24) in short
intervals.
Check the funnel feeder (7) is empty and clean.
Connect the power supply and switch ON the machine to shred the material. (Fig. 4)
Turn the adjustor screw (4) slowly clockwise until you hear scraping noises. Small
aluminium shavings will come out.
Switch OFF the machine and unplug the power supply.
10 SHREDDING TIPS
Heavy material or branches may result in blocking of the cutting blades during continuous
cutting.
Soft materials, such as leaves or stems may block the feeding opening.
Always feed the material to be chopped from the right corner of the feeding funnel.
Check the material to be chopped carefully. Make sure there is no contact with stones or
nails as these could damage the shredder seriously.
To release blocked material, switch the shredder on and press the reverse button. The
blade drum will release the jammed shredding material. If it is still blocked, you can
increase the distance between the anvil & the drum knife (see described before in this
manual). Try reverse run again to free the blocked material. Readjust the anvil to your
personal choice.
Keep hold of branches while feeding them into the shredder until they are automatically
drawn in.
Keep to the working speed of the shredder and do not overload it.
To protect the shredder from clogging, shred wilted garden waste that has been left for a
few days and shred thin twigs alternately with branches.
Before you shred roots, remove any remaining soil and stones from them. Do not shred
soft, damp material such as kitchen waste, but take it straight to the compost.
Keep a few dry branches for the end, as they will help clean the shredder.
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Powerplus POWXG6462 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Powerplus POWXG6462

Powerplus POWXG6462 Bedienungsanleitung - Deutsch - 15 seiten

Powerplus POWXG6462 Bedienungsanleitung - Holländisch - 15 seiten

Powerplus POWXG6462 Bedienungsanleitung - Französisch - 15 seiten

Powerplus POWXG6462 Zusatzinformation - Alle Sprachen - 4 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info