Bedienungsanleitung Powertec Garden GAK 710 TELE 05167 (Seite 11 von 28) (Deutsch, Englisch, Französisch)

621129

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Saw chain (chain): Chain loop with cutting teeth that cut

wood. The chain is engine-powered. The chain leans against

the chain bar.

Chain wheel: Gear wheel driving the chain.

Switch: A device closing or opening the electrical circuit to the

saw engine.

Switch fuse: A device eliminating unattended saw starting.

Starter: A device switching the saw on and off. The saw is

started by pressing the starter. The saw is switched off by

releasing the starter.

Sawing out (pruning): Steps for cutting branches on a living

tree.

Bottom cut: Upward guided cut from the bottom side of the

tree trunk or branch. Performed in a standard cutting position

and with the chain bar point cut.

Assembly

Chain bar and saw chain fitting:

CAUTION: The cutting edges on the chain are sharp.

Wear protective gloves when handling the chain.

IMPORTANT: Vice the pole saw carefully when fitting it.

1. Remove the chain wheel cover (pic. 1/5)

2. Fit the chain to the bar (pic. 5) (see the chain rotation

direction in pic. 4!)

3. Loosen the clamping screw (pic. 5/B) using the spanner

included.

4. Fit the chain to the chain wheel and insert the bar (long

bar opening and bar boring match the chain bar screw

and clamping screw pic. 6).

5. Fit the cover (pic. 7) and tighten it slightly (by hand).

CAUTION: Do not fit the chain against the rotation

direction. If the chain is the other way round, the saw

strongly vibrates and does not cut (pic. 4)

Fitting the handle:

Fit the handle as shown in pic. 18.

Folding function:

Assemble the pole saw as shown in pic. 9 and tighten it with

two screws.

Chain tension calibration

CAUTION: Make always sure the chain is tightened

properly. A loose chain increases the risk of backlash. A

loose chain could get out of the guide. It could injure the

operator and damage the chain. A loose chain causes

quick wear of the chain, chain bar and chain wheel.

Pic. 5:

A Chain tension

B Chain loosening

1. Before calibrating the chain, make sure the chain bar nut

(pic. 1/6) is only tightened by hand.

2. Turn the clamping screw clockwise so that the chain gets

tightened. (pic. 5/A)

Notice: The chain is tightened properly when fitted in

a way it cannot get out of the guide when the

appliance is being operated. The chain must move

freely. If the chain is not moving freely, release it by

turning the clamping screw counter-clockwise.

3. After the chain is tightened properly, tighten the chain bar

nut (pic. 1/6), if not tightened - the chain bar is moving

and the chain tension is getting released. This increases

the risk of backlash and can even cause damage to the

saw. Notice: The new chain gets expanded. Check the

new chain after first minutes of operation. Let the chain

cool down and then recalibrate the chain tension.

Chain lubrication with oil

Check the oil level after each use of the saw. Make sure there

is always sufficient amount of oil in the storing reservoir.

Important basic safety instructions

Please read carefully the following safety regulations and

Operating Instructions before working with the appliance. If

the appliance is also handed to other persons, provide them

with the Operating Instructions. Keep the Operating

Instructions!

Package: To prevent the appliance against damage, it is in a

package during transport. Packages are raw materials and

can therefore be reused or recycled.

Please read carefully the Operating Instructions and follow all

included instructions. Use these Operating Instructions to

familiarise with the appliance, how to use it properly and with

the safety instructions. Please keep these instructions for

future reference.

• The saw must not be used if the operator is tired or under

the influence of alcohol, pharmaceuticals or drugs.

• Appliances not being used must be kept in a dry and

locked place, inaccessible to children.

• Keep the tools sharp and clean so that working with them

is better and safer. Check regularly the appliance cable

and have it replaced by a recognised professional if

damaged.

• Check regularly the extension cable and have it replaced

if damaged. Approved extension cables with proper

marking to be used outdoors only.

• Applicable accident prevention regulations, generally

recognised safety-technical rules must be followed.

• Unplug the appliance for any adjusting and servicing.

• All protective and safety equipment must be immediately

refitted after finishing any repair or servicing work.

• Any damaged or defective protective equipment must be

immediately replaced.

• Any electrical installation, repair and servicing may only

be performed by professionals.

• Do not wear any loose clothing and jewels. They could

get caught by the rotating chain. Wear a hairnet if you

have long hair! Wear a respirator (when working in a

dusty environment).

• Do not use the cable to pull the plug out of socket. Protect

the cable against excess temperatures, oil and sharp

edges.

• Wear heavy protective gloves, safety shoes with safety

steel insole and anti-slip sole.

• Do not switch the appliance on if turned over or not in the

working position.

• Keep the appliance out of reach of other persons,

especially children and pets.

• Work under adequate visibility only.

• If work is interrupted, keep the appliance in a safe place.

• Never use the appliance when raining or in a damp or wet

environment.

• All parts of the appliance must be regularly checked for

any damage or aging. The appliance must not be used if

not in a perfect state.

• Original spare parts to be used for repairs only.

• Before putting the appliance into operation and after any

impact, check it for any signs of wear or damage and

have any necessary repairs executed.

• Never use spare parts and accessory equipment not

specified or recommended by the manufacturer.

• Make sure that other items do not cause short circuit on

the appliance contacts.

• Persons who are not able to operate the appliance

due to their physical, sensory or mental skills or their

lack of experience or knowledge must not use the

appliance.

• If the appliance shows any visible damage, it must

not be put into operation.

Bei mir ist der Hebel von schnell auf langsam Schildkröte-Hase, von meinem Rasenmäher Power Tec Garden Baujahr 2012/12/EB 041545 kaputt gegangen Wie heißt das Ersatzteil und bekomme ich es Von Ihnen? was kostet das und gibt es noch eine Liste oder Bedienungsanleitung von diesen Rasenmäher? Es wäre toll wenn ich eine Nachricht von Ihnen bekommen könnte.Meine Emailadresse lautet : Brigitte.Heidmueller@gmx.de ich wünsche einen schönen Abend und lassen Sie mich nicht solange warten,der Rasen wächst und will gemäht werden. Vielen Dank für Ihre Mühe und Mit freundlichen Gruß Frau Heidmüller Eingereicht am 26-4-2017 18:33
Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.

Neu registrieren

Registrieren auf E - Mails für Powertec Garden GAK 710 TELE 05167 wenn:

neue Frage gestellt werden
neue Handbücher vorhanden sind

Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.

Powertec Garden GAK 710 TELE 05167 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.