621129
12
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
There may be significant risks as a result of any
unauthorised repairs.
The same regulations apply to accessory parts.
Güde GmbH & Co. KG will not be held liable for any
damage caused by the following:
Damage to the appliance as a result of mechanical
influences and overloading.
Change to the appliance
Use for purposes other than those specified in the
Operating Instructions.
All safety instructions need to be necessarily
followed to prevent any injuries and damage.
Important appliance-specific safety
instructions
A flat and non-slip place of work with sufficient free
movement must be provided before working with the pole
saw.
Switch the pole saw off and unplug it when leaving the
place of your work.
Remove any wooden waste and items no longer needed
from the place of your work.
Do not cut near flammable liquids or gases.
Defective chains must be immediately replaced.
Sawing branches out should be done on a sawhorse.
Watch out for falling branches. Check the tree to be saw
out. Make a room for falling branches.
Do not stand on a ladder or any other unstable equipment
when using the pole saw. Use both hands when working
with the saw. Apply firm, constant pressure on the chain
saw when cutting. Do not use the pole saw for sawing out
branches with a diameter exceeding the chain bar.
Keep other persons out of reach of the cutting end of the
pole saw – and in a safe distance from the place of your
work.
Do not stand directly under the branch to be cut off. Stand
always outside the falling branches.
Caution: The saw may only be used in a system with
safety switch against stray current (FI)!
Saw head angle adjustment
Caution! Adjustment to be performed with the
appliance being switched off only!
The saw head can be locked in 3 various cutting angles, which
enables individual working.
Press the locking screw (pic. 1/4) and put the saw head to the
required working position. Fixate the saw head in the required
position using the locking screw (pic. 1/4).
Safety instructions fort he operator
Do not use the appliance before reading carefully the
Operating Instructions.
Follow all safety instructions included in the Operating
Instructions.
Behave responsibly to other persons.
Walk, do not run when working.
Use the right working clothes at all times.
Operation
1. Connect the saw with the extension cable. Plug the
extension cable.
2. Use both hands to hold the saw. When operating
the chain saw (pic. 10), use only the specified points of
gripping. Hold the saw properly. Thumbs and fingers
must embrace the chain saw handle and pole.
3. Make sure your legs are positioned properly. Distribute
your weight evenly to both legs.
4. To start the appliance, press the stop first and then
On/Off. By this, the chain saw will be started. The chain
saw gets switched off by releasing On/Off. Make sure
the saw runs at full speed before performing first cut.
CAUTION: To support the saw, use the stop surface
on the cutting head at all times!
After starting the cut, guide the rotating chain to the wood.
Keep the chain saw firmly in hands to prevent any rejection or
slip (lateral movement) of the saw.
5. Guide the chain saw with slight pressure. Do not
overload the chain saw. Otherwise, the engine may get
overloaded and burn down. The saw works better and
safer at the specified speed.
6. Move away from the cut with the chain saw when still
running at full speed. Switch the chain saw off by
releasing the starter. The chain saw must be stopped to
the full extent before being put away.
CAUTION:
Prevent any backlash. A backlash may cause serious
injuries.
Do not use the chain saw when standing on a ladder or
any other unstable equipment and when in an unstable
position.
Contact a professional to help you if circumstances
require use of bigger appliances.
Marking
Product safety:
Product corresponds to
applicable EU standards
Tested by Intertek
Prohibitions:
General prohibition
(in connection with another
icon)
Do not use the appliance
when raining
No pulling / carrying by cable
Warning against dangerous
backlash!
Warning:
Warning/Caution
Warning against flying
items
Keep safe distance
Commands:
Read the Operating
Instructions!
Wear protective glasses
and ear protectors!
12
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

powertec-garden-gak-710-tele-05167

Suche zurücksetzen

  • Bei mir ist der Hebel von schnell auf langsam Schildkröte-Hase, von meinem Rasenmäher Power Tec Garden Baujahr 2012/12/EB 041545 kaputt gegangen Wie heißt das Ersatzteil und bekomme ich es Von Ihnen? was kostet das und gibt es noch eine Liste oder Bedienungsanleitung von diesen Rasenmäher? Es wäre toll wenn ich eine Nachricht von Ihnen bekommen könnte.Meine Emailadresse lautet : Brigitte.Heidmueller@gmx.de ich wünsche einen schönen Abend und lassen Sie mich nicht solange warten,der Rasen wächst und will gemäht werden. Vielen Dank für Ihre Mühe und Mit freundlichen Gruß Frau Heidmüller Eingereicht am 26-4-2017 18:33

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Powertec Garden GAK 710 TELE 05167 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info