Bedienungsanleitung Pride Colt Twin (Seite 38 von 48) (Englisch)

721988

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

www.pridemobility.com Colt Twin

VIII. BASIC TROUBLESHOOTING

Any electromechanical device occasionally requires some troubleshooting. However, most of the problems that

may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because

the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge.

DIAGNOSTIC FAULT CODES

The diagnostic fault codes for your scooter are designed to help you perform basic troubleshooting quickly and

easily. A diagnostic flash code will flash from the status LED in the event one of the conditions listed below

develops. Your scooter will also emit a beep code to indicate the system fault.

NOTE: Your scooter will not run unless the fault code condition is resolved and the scooter has been

turned off, then turned back on.

FAULT CODE CONDITION SOLUTION

! (1)

Battery charge is low. Charge batteries as soon as possible.

! ! (2)

Battery charge is too low to operate

the scooter.

Charge batteries.

! ! ! (3)

The scooter’s battery voltage is too

high to operate the scooter, or the

charger is still connected to charger

port.

Unplug charger and/or turn key off, then

back on again.

! ! ! ! (4)

Current limit time out.

urn the scooter off for a few minutes,

then turn your scooter back on.

! ! ! ! ! (5)

The manual freewheel lever is in the

(forward) freewheel position.

Remove the key from the key switch,

then push the manual freewheel lever to

the (rear) drive position, and restart your

scooter.

! ! ! ! ! ! (6)

Throttle control lever not at centre

position at start up.

Return the throttle control lever to centre

position, turn scooter off, and then back

on.

! ! ! ! ! ! ! (7)

Speed pot error.

Contact your authorised Pride Dealer for

assistance.

! ! ! ! ! ! ! ! (8)

Motor volts error.

Contact your authorised Pride Dealer for

assistance.

! ! ! ! ! ! ! ! ! (9)

Other internal errors.

Contact your authorised Pride Dealer for

assistance.

What if all the systems on my scooter seem to be dead?

! Make certain that the key is in the “on” position.

! Check that the batteries are fully charged.

! Push in the main circuit breaker reset button. See III. “Your Scooter.”

! Make certain that both battery harnesses and the front-to-rear harness are firmly connected. See VII. “Disas-

sembly and Assembly.”

! Be sure the power down timer feature has not been activated. See V. “Operation.”

What if my scooter does not move when I engage the throttle control lever?

! When the manual freewheel lever is pushed forward, the brakes are disengaged and all power to the motor/

transaxle assembly is cut.

! Push rearward on the manual freewheel lever, turn the scooter off and then turn the scooter on to return to

normal scooter operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pride Colt Twin Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info