Bedienungsanleitung Pride Go Go ELITE TRAVELLER PLUS (Seite 28 von 108) (Englisch, Französisch, Spanisch)

514962

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

28 Travel Scooter Series

VI. DISASSEMBLY AND ASSEMBLY

DISASSEMBLY

You can disassemble the Travel Scooter into several pieces: the seat, the under-seat storage, the rear section, the front

section, the basket, the battery pack, and the battery shroud (models 83 and 84 only). See ﬁ gure 31. No tools are

required to disassemble or assemble your Travel Scooter. Always disassemble or assemble your Travel Scooter on a

level, dry surface with sufﬁ cient room for you to work and move around—about 5 feet (1.5 meters) in all directions.

Remember that some Travel Scooter components are heavy and you may need assistance when lifting them.

WARNING! Do not lift weight beyond your physical capability. Ask for assistance when necessary

while disassembling or assembling your Travel Scooter.

WARNING! Do not pick up the seat frame or scooter by the armrests. They are free to pivot, and

you may lose control of the seat if they do so.

IDENTIFICATION KEY

* Indicates

Lifting Points

1. Seat

2. Under-seat Storage

3. Rear Section

4. Front Section

5. Basket

6. Battery Pack

7. Battery Shroud

DISASSEMBLY PROCEDURES - MODELS 36, 83, AND 84

1. Remove the key from the key switch.

2. Lock the tiller in the straight ahead position by pushing the tiller lock knob

in and turning it clockwise 90°. See ﬁ gure 32. The front wheel must face

forward in order to lock the tiller.

3. Remove the seat by lifting it straight up and off of the Travel Scooter. If you

encounter resistance when removing the seat, disengage the seat rotation

lever and swivel the seat back and forth while lifting up on the seat.

4. Remove the rear shroud by lifting it straight up and off of the Travel Scooter.

(Models 83 and 84 only).

5. Disconnect the battery harness. See ﬁ gure 21.

6. Disconnect the front-to-rear harness. See ﬁ gure 21.

7. Disconnect the battery tie-down strap. (Models 83 and 84 only). See ﬁ gure 21.

8. Remove the battery pack from the Travel Scooter by lifting it straight up

and off of the Travel Scooter.

Figure 32. Tiller Lock Knob

DISASSEMBLY PROCEDURES - MODELS 39, 40LX, 40X, 44X, 40E, 44E, 44LX, 49, 50LX, 54LX, 53,

53HD, 54, 54HD, 66, 67, 73, 74, AND JAZZY ZTS

1. Remove the key from the key switch and then lock the tiller in the straight ahead position by pushing the tiller lock

knob in and turning it clockwise 90°. See ﬁ gure 32. The front wheel must face forward in order to lock the tiller.

2. If equipped, remove under-seat storage. See Figure 27.

3. Remove the seat by lifting it straight up and off of the Travel Scooter. If you encounter resistance when removing

the seat, disengage the seat rotation lever and swivel the seat back and forth while lifting up on the seat.

4. Remove the battery pack by lifting the pack straight up and off of the Travel Scooter.

NOTE: Please check the Travel Scooter Features Table on the inside of the front cover to determine if your

Travel Scooter has a frame release lever or a lock-up pin before attempting to separate the frame.

Figure 31. Disassembled Travel Scooter

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pride Go Go ELITE TRAVELLER PLUS Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pride Go Go ELITE TRAVELLER PLUS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info