Bedienungsanleitung Pride Go Go ELITE TRAVELLER PLUS (Seite 30 von 108) (Englisch, Französisch, Spanisch)

514962

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

30 Travel Scooter Series

Any electromechanical device occasionally requires some troubleshooting. However, most of the problems that

may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because

the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge.

DIAGNOSTIC CODES

The diagnostic codes for your Travel Scooter are designed to help you perform basic troubleshooting quickly

and easily. A diagnostic code will sound and/or ﬂ ash in the event one of the conditions listed below develops.

Depending on the model you own, your Travel Scooter will communicate by one of the coding methods as follows:

1. A diagnostic code will begin, depending on model, with a series of fast beeps and/or ﬂ ashes directly followed

by slower beeps and/or ﬂ ashes which indicates the actual code. The code is only beeped and/or blinked once.

To repeat the diagnostic code, remove the key, then reinsert it and turn it to the “on” position, OR

2. A diagnostic code will identify the condition, pause, then repeat the code. The diagnostic code will continue

to alert you in this manner until the scooter is turned off.

NOTE: Your Travel Scooter will not run unless the diagnostic code condition is resolved and the Travel Scooter

has been turned off, then turned back on.

DIAGNOSTIC CODE CONDITION SOLUTION

■

(1)

Battery voltage is too low to operate the

Travel Scooter.

Charge batteries as soon as possible.

■■

(2)

Battery charge is too low. Charge batteries.

■■■

(3)

The Travel Scooter’s battery voltage is too high

to operate the scooter, or the charger is still

connected to the off-board charger port.

Unplug charger and/or turn key off, then back on

again. If traveling down a slope, reduce Travel

Scooter speed to the minimum setting.

■■■■

(4)

Current limit time out. Turn the Travel Scooter off for a few minutes,

then turn your Travel Scooter back on.

■■■■■

(5)

The manual freewheel lever is in the (forward)

freewheel position.

Remove the key from the key switch, then

push the manual freewheel lever to the drive

(rearward) position and restart your Travel

Scooter.

■■■■■■

(6)

Throttle control lever not at center position at

start up.

Verify that the batteries are fully charged. If

the batteries are fully charged, then return the

throttle control lever to center position, turn

Travel Scooter off then back on.

■■■■■■■

(7)

Speed pot error. Contact your authorized Provider for assistance.

■■■■■■■■

(8)

Motor volts error. Contact your authorized Provider for assistance.

■■■■■■■■■

(9)

Other internal errors. Contact your authorized Provider for assistance.

VII. BASIC TROUBLESHOOTING

What if my Travel Scooter does not move when I press the throttle control lever?

 When the manual freewheel lever is pushed forward, the brakes are disengaged and all power to the motor/

transaxle assembly is cut.

 Pull back on the manual freewheel lever, turn the Travel Scooter off, and then back on to return to normal

operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pride Go Go ELITE TRAVELLER PLUS Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pride Go Go ELITE TRAVELLER PLUS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info