Bedienungsanleitung Pro-form G880 (Seite 6 von 18) (Englisch)

708084

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

TROUBLESHOOTING

Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediate-

y. The weight bench can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.

TIGHTENING THE CABLES

oven cable, the type of cable used on the weight bench, can stretch slightly when it is first used. If there is

slack in the cables before resistance is felt, the cables should be tightened. Slack can be removed from the

cables in several ways:

3. Attach the Leg Lever Bracket (5) to the Bench

Frame (1) with two M10 x 68mm Bolts (113) and

wo M10 Nylon Locknuts (97).

ttach the Weight Tube (25) to the Leg Lever (4)

with an M8 x 58mm Bolt (106), two M8 Washers

(100), a 10mm Spacer (30), and an M8 Nylon

Locknut (96).

Apply grease to an M10 x 68mm Bolt (113).

Attach the Leg Lever (4) to the Leg Lever Bracket

(5) with the Bolt and an M10 Nylon Locknut (97).

Do not overtighten the Locknut; the Leg Lever

must be able to pivot easily.

5. Attach the Backrest Bracket (7) to the Backrest

Tubes (8) with four M10 x 45mm Bolts (112), four

M10 Washers (99), and four M10 Nylon Locknuts

(97). Make sure the Backrest Tubes are orient-

ed so that the indicated holes are closer to

the bottom. Do not tighten the Locknuts yet.

4. Apply grease to an M10 x 78mm Bolt (110). Align

the lower hole in the Adjustment Lever (11) with

the indicated tube on the Bench Frame (1). Attach

the Adjustement Lever with the Bolt and an M10

Nylon Locknut (97).

Do not overtighten the

Locknut; the Adjustment Lever must be able

to pivot easily.

See the inset drawing. Hold the handle on the

Adjustment Lever (11) so that the upper hole is

above the Bench Frame (1). Tighten the M10 x

62mm Flat Head Screw (27) through the

Adjustment Lever, above the Bench Frame.

Make

sure that the threads of the Screw show

through the Adjustment Lever. Do not over-

tighten the Screw.

100

113

Grease

Tube

106

110

Holes

112

See drawing 1. To tighten the cables, remove the

M10 Nylon Locknut (97) and the M10 x 45mm Bolt

(112) from the lower 90mm Pulley (90), Small Cable

Trap (125), two Half Finger Guards (133), and the

Pulley Plates (72). Reattach the Pulley, the Cable

Trap, and two Half Finger Guards at a set of holes

closer to the center of the Pulley Plates with the Bolt

and Locknut.

Make sure the Cable Trap is oriented

to hold the Low Cable (82) in the groove of the

Pulley.

See drawing 2. Additional slack can be removed

from the cables by tightening a cable into the M6

Nylon Locknut (124) inside a Cable End Clip (85). To

do this, first pull the Clip Cover (84) back. Then, hold

the crimp on the Cable with a pair of pliers and insert

a screwdriver between the Locknut and the Clip.

Rotate the screwdriver, the Clip, and the Locknut

together until the slack is removed. Replace the

Cover over the clip.

Do not overtighten the cables. If a cable slips off the pulleys repeatedly

, it may have become twisted.

Remove the cable and re-install

it.

If the cables need to be replaced, see ORDERING REPLACEMENT

PARTS on the back cover of this manual.

112

125

133

124

Cable

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pro-form G880 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pro-form G880

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info