Bedienungsanleitung Pro-form Performance 1450 - PFTL14511 (Seite 27 von 40) (Englisch)

553999

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

HOW TO USE THE MAINTENANCE MODE

The console features a maintenance mode that allows

ou to calibrate the incline and speed of the treadmill,

update the console firmware, calibrate the screen,

iew technical information, and perform a network test.

1. Select the settings mode.

See step 1 on page 25.

2. Select the maintenance mode.

Touch the Maintenance button in the lower right

corner of the screen to

enter the maintenance

mode.

The maintenance mode

main screen will show

information about the model and version of the

treadmill. If the console is connected to the con-

troller of the treadmill, the controller dot will be

green; if it is not, the dot will flash. If the treadmill is

connected to your wireless network, the network

dot will be green; if it is not, the dot will be black.

3. Calibrate the incline system of the treadmill.

Touch the Calibrate Incline button. Then, touch the

Begin button to calibrate the incline system. The

treadmill will automatically rise to the maximum in-

cline level, lower to the minimum incline level, and

then return to the starting position. This will cali-

brate the incline system. Press the Cancel button

to return to the maintenance mode. When the in-

cline system is calibrated, touch the Finish button.

IMPORTANT: Keep pets, feet, and other objects

away from the treadmillwhile theincline system

is calibrating. In an emergency, pull the key

from the console to stop the incline calibration.

4. Calibrate the speed of the treadmill.

Calibrate the speed of the treadmill only if in-

tructed to do so by an authorized service repre-

sentative.

Note: The Calibrate Speed button may not be en-

abled on your treadmill.

5. Update the console firmware.

For the best results, regularly check for

firmware updates.

Touch the Firmware Update button. Next, touch

the WiFi button to check for firmware updates

using your wireless network. Then, touch the Begin

button to check for updates or the Cancel button to

return to the maintenance mode.

To avoid damaging the treadmill, do not turn

off the power or remove the key while the

firmware is being updated.

Note: If you cannot update the console firmware

over your wireless network, you can update the

firmware using a USB drive. Touch the USB button

to install firmware updates using a USB drive. Go

to www.iFit.com and download the firmware update

onto your USB drive. Safely remove the USB drive

from your computer and plug it into the USB port

on the top of the console. Touch the Begin button

to update the firmware or touch the Cancel button

to return to the maintenance mode.

The screen will show the progress of the update.

When the update is complete, the treadmill will turn

off and then turn back on. If it does not, press the

power switch into the off position. Wait for several

seconds, and then press the power switch into the

reset position. It may take a few minutes for the

console to be ready for use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pro-form Performance 1450 - PFTL14511 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info