Bedienungsanleitung Pro-User PSI1000TX (Seite 5 von 82) (Deutsch, Englisch, Holländisch, Französisch)

807468

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

• Avoid getting electrolyte on your skin or clothes. It is acidic and can cause burns. If battery

acid contacts skin or clothing, wash immediately with water. Baking soda neutralizes lead

acid battery electrolyte. If electrolyte gets into your eyes, immediately ﬂood your eyes with

running cold water for at least 20 minutes and get medical attention immediately. Eye

protection is therefore recommended.

• Always keep metal objects or other materials that can short circuit the terminals of the

battery or the inverter securely away.

• Power-o the device before making or breaking the connections to the battery.

• Observe technical instructions of the seller or the manufacturer of your battery.

• Check if all connections are tight and clean. Loose or dirty connections could result in

overheating, electrical sparks and ﬁre. Use terminal grease where required.

• Never smoke or allow a spark or ﬂame in vicinity of the battery.

• Never try to charge a damaged or frozen battery.

• Do not place the device directly on top of the battery or vice versa or on a surface

constructed from combustible material.

• Read your car´s owner's manual. Some vehicle manufacturers may have special requirements

before charging or discharging the vehicle´s battery (e.g. fuses that have to be removed or

certain security demands).

Environment

EnvironmentEnvironment

Environment

• Only use the product in environments from 0°C ~ 45°C.

• Do not operate the product in damp, wet or dusty environments: Never expose the inverter

to rain or snow. Doing so may result in damage to the inverter or other equipment installed in

the system or result in electric shock or ﬁre. Do not operate the unit in explosive

atmospheres, such as in the presence of ﬂammable liquids, gases or dust. Do not put

batteries, or anything that should be protected from sparks around the inverter. Doing so

may result in ﬁre or explosion.

• To avoid heat accumulation, do not cover the device. To prevent overheating , ensure that air

inlets and ventilation is not obstructed. Do not expose the device to a heat source (such as

direct sunlight or heating). Avoid additional heating of the device in this way.

Electrical Cables

Electrical CablesElectrical Cables

Electrical Cables

• If cables have to be fed through metal holes or other walls with sharp edges, use ducts or

cable bushings to prevent damage.

• Do not lay cables which are loose or bent next to electrically conductive material (metal).

• Do not pull on the cables.

• Avoid to lay 230 V AC mains cable and 12 V DC cables in the same duct.

• Prevent all cables from being stepped on, tripped over, or being damaged by e.g. sharp edges

or hot surfaces.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pro-User PSI1000TX Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info