Bedienungsanleitung Proficare PW 3006 FA (Seite 33 von 58) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

814854

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

PC-PW3006 FA_IM 18.09.17

The signal is generally safe! However, please read our spe-

cial safety instructions!

The method of measurement is referred to as “bioelectric

impedance analysis” (BIA), a factor which is based on the

relationship between body weight and associated body water

percentages as well as on other biological data (age, gender,

body weight).

Use

NOTE:

• The buttons are sensor touch buttons. Touch the but-

tons lightly with a nger to execute the function.

• The scales are factory set with the units “kg” and “cm”.

To change the settings to “lb” or “st” as well as “ft”, proceed

as follows:

1. Turn on the scales by light pressure with the foot onto the

weighing surface.

2. Press the “kg / lb / st” button on the underside of the scales

repeatedly, until the required weight unit is displayed. The

unit for the height also automatically changes.

Weighing Function

1. Place the scale on a hard, at surface (avoid carpets). An

uneven oor contributes to inaccurate measurements.

2. Stand on the scales with both feet. The appliance

switches on automatically.

3. Distribute your weight equally and wait for the scale to

determine your weight.

4. The digits on the display will ash before your exact

weight will be shown.

• In order to extend the battery life, the appliance will

automatically turn off 25 seconds after you have stepped

off the scale.

• If there is no weight determination while “0.0” is shown,

the scale will shut off automatically after 25 seconds.

Saving Personal Data

NOTE:

• The scale has default values that you can change, as

described below.

• Carry out the following steps in sequence and within a

few seconds. Otherwise, the appliance will automati-

cally cancel input mode.

• Holding one of the buttons ( / ) pressed for approx.

2 seconds selects fast mode.

1. Press the button SET. The memory location selected

last ashes on the display (for example P0). Conrm the

setting by pressing SET or select another memory space

by pressing the / button. Then press SET to go to the

next setting.

2. The symbol for “male” or “female” will ash. Conrm the

setting by pressing SET or use the / button to choose

the symbol for your gender. Then press SET to go to the

next setting.

3. The setting AGE will ash. Select your age by pressing

or button. Conrm your entry by pressing SET.

4. The height setting will ash. Select your height by press-

ing or button. Conrm your entry by pressing SET.

5. Then you will see the symbol of the gender, the user stor-

age location and the previously selected weight indication

on the display (0.0 kg / 0.0 lb / 0: 0 st).

You now have the following options:

• Press the SET button repeatedly to display the settings

again or to change them.

• You can set further preset locations. Proceed as de-

scribed above.

• You can immediately start measuring.

Measurement and Analysis

Record your personal data in the memory.

NOTE:

• The analysis scale will only work correctly when you

are standing on the contact surfaces barefoot and with

slightly moistened foot soles, if possible. Completely

dry foot soles can lead to unsatisfactory results as they

have a conductivity that is too low.

• If necessary wipe the contact surfaces to improve

results.

• Due to the signicant uctuation of body fat, it is difcult

to attain a standard value. Therefore, to obtain consist-

ent data, always measure at the same time of day.

• Amongst other things, our body consists of body

fat, body water, muscle mass and bone weight. The

obtained values may differ due to individual water reten-

tion within these main components. This is normal and

highly dependent on nutrition and lifestyle.

1. Press the SET button. Use the / button to select

the stored position at which your data is saved. The

location ashes for approx. 3 seconds. Then you will see

the symbol of the gender, the user storage location and

the previously selected weight indication on the display

(0.0 kg / 0.0 lb / 0: 0 st).

2. Stand on the contact surfaces (5) of the scales with both

feet.

3. Firstly your weight will ash on the display. The analysis

starts after the display has stopped ashing. You’ll see a

treadmill “ ” in the display during the analysis. Remain

on the scales until the last display (KCAL) has appeared.

The following results are displayed one after the other:

1. The body fat proportion in % ( ) and the rating

2. The proportion of body uid % ( )

3. The proportion of muscle mass in % ( )

4. The bone weight in % ( )

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proficare PW 3006 FA Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info