490600
17
Zoom out
Zoom in
Vorherige Seite
1/136
Nächste Seite
17
5.5 Emission levels
Levels determined in accordance with
EN 60 745 are typically:
Sound pressure level L
PA
= 91 dB (A)
Noise level L
WA
= 102 dB (A)
Uncertainty K = 1.5 dB
CAUTION
Operating noise
Damage to hearing
Use ear protection!
Vibration emission value a
h
(vector sum for
three directions) and uncertainty K meas-
ured in accordance with EN 60 745:
a
h
= 1.4 m/s
2
Uncertainty K = 1.5 m/s
2
The emission values speci ed (vibration,
noise) were measured in accordance with
the test conditions stipulated in EN 60 745
and are intended for machine comparisons.
They are also used for making preliminary
estimates regarding vibration and noise
loads during operation.
The emission values speci ed refer to the
main applications for which the power tool
is used. If the electric power tool is used for
other applications, with other tools or is not
maintained suf ciently prior to operation,
however, the vibration and noise load may
be higher when the tool is used.
Take into account any machine idling times
and downtimes to estimate these values
more accurately for a speci ed time period.
This may signi cantly reduce the load dur-
ing the machine operating period.
6 Commissioning and
Operation
WARNING
Risk of injury, if the tools are used
with wrong supply power.
The voltage speci cations on the rating plate
must correspond with the mains voltage.
Equipment marked with 230 V can also be
connected to 220 V / 240 V.
Check that the plug type is the same as the
socket type.
Adjustment of the riving knife
WARNING
Risk of injury, if the riving knife is not
correctly adjusted.
The riving knife [2-6] must always be used
for safety reasons. The riving knife prevents
the saw blade from becoming jammed when
making lengthwise cuts.
1-5
2-6
2.5 – 5 mm
2.5 – 5 mm
Loosen screw [1-5], adjust the riving knife
[2-6] and retighten the screw (see gure).
Check the function of the swinging guard
[1-8].
Switching On/Off
Switching On:
Press the safety button [1-1].
Press the on-off switch and hold depressed.
Note: The on-off switch cannot be locked
on.
Switching Off:
Release the on-off switch [1-2].
7 Adjustment
WARNING
Risk of electric injury.
Before any manipulation with the tool
make sure to unplug the mains socket
outlet.
7.1 Electronic Motor Control
Starting current limiting
The electronically controlled smooth start
takes care that the machine starts without
jerk. As a result of the machine’s reduced
starting current, a 16 A fuse is suf cient.
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Protool CSP 56-2 EB wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info