Bedienungsanleitung Protool CSP 56-2 EB (Seite 19 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490600

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

7.7 Replacing the Saw Blade

WARNING

Before exchanging the saw blade, pull

the mains plug from the power sup-

ply socket.

Wear protective gloves!

The spindle locking button [1-3] may

be pressed only when the saw blade

is at a standstill.

Removing the saw blade

Swing back the protective guide [1-8] with

the lever [1-6].

Depress the spindle locking button [1-3].

Unscrew the clamping screw [2-2] with the

Allen key [2-1] from motor spindle [2-7].

Remove the clamping ﬂ ange [2-3] and the

saw blade [2-4].

Saw blade installation

The sawing performance and the quality of

the cut depend essentially on the condition

and tooth form of the saw blade. Therefore,

use only sharp saw blades that are suitable

for the material to be worked.

Swing back the swinging guard [1-8] with

the lever [1-6].

Depress the spindle locking button [1-3].

Install a suitable saw blade according to the

illustration and tighten. Take care that the

mounting ﬂ ange [2-5] and the clamping

ﬂ ange [2-3] are correctly positioned.

WARNING

Observe for installation: The cutting

direction of the teeth (arrow on the

saw blade) must match the direction

of the arrow on the guard.

Check the function of the swinging

guard.

8 Operating Instructions

► Do not cut into nails, screws, etc.

► Do not work with materials containing

asbestos.

► Do not use saw blades that have cracks

or that are damaged.

► Under no circumstances use abrasive

disks!

► Saw blades of highly alloyed, high-speed

steel (HSS-steel) must not be used.

► Feeding too fast signiﬁ cantly reduces the

performance of the machine and short-

ens the life of the saw blade.

► Use only sharp saw blades in perfect con-

dition.

► Uncoated saw blades can be protected

from corrosion with a thin coat of acid-

free oil.

► Resin and glue on the saw blade cause

poor cutting results. Therefore, clean the

saw blade immediately after use.

Working different materials

Wood

The proper selection of the saw blade is

dependent on the type and quality of the

wood as well as whether the wood is to be

sawed along or across the grain.

Beech and oak dust is especially detrimental

to health and therefore should be worked

only with vacuum dust extraction.

Plastic

When cutting plastic, especially PVC, long,

spiral shaped shavings are produced that

can be electrostatically charged.

This can cause the ejector to become clogged

and the swinging protective guard [1-8] to

stick. The use of a vacuum cleaner for dust

extraction is recommended.

Apply the machine running against the work-

piece and carefully start sawing. Then saw

steadily and without interruption so that the

saw teeth have less chance of sticking.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool CSP 56-2 EB Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info