Bedienungsanleitung Protool CSP 56-2 EB (Seite 20 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490600

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Non-ferrous Metals

Use only a suitable and sharp saw blade.

This ensures a clean cut and prevents jam-

ming of the saw blade.

Apply the machine running to the workpiece,

carefully start sawing and then saw with

slow feeding and without interruption.

For proﬁ les, always start the cut on the small

side; for U-proﬁ les, never start the cuts on

the open side.

Support long proﬁ le, otherwise the saw

blade can become jammed when the proﬁ le

tips over and the machine can “kick back”.

Material with Mineral Content

(Light building material)

► Only dry cutting is permitted.

► Use vacuum dust extraction. The vacu-

um cleaner must be suitable for masonry

dust.

9 Use of Accessories

The machine has a longitudinal slot at the

base plate underside to take up a guide rail.

With this guide rail, it is made easy to carry

out larger cuts.

PROTOOL Guiding System

For easy and safe handling when cutting

large work pieces as well as for achiev-

ing exact angle cuts, the use of the

GRP 800/1400/3000-2 guiding system is

recommended.

With it, clean cuts are possible by preci-

sion guiding of the machine along a cutting

line. In addition, the hard anodising of the

guide rail makes possible easy gliding of the

machine and thereby reduces the required

advancing force while improving the work

progress.

The saw’s side suction clearance on the bar

is possible to adjust with the adjusting nobs

[6-1].

Mounting the Guide Rail

(GRP 800/1400/3000-2)

The mounting of the guide rail [7-1] takes

place with the use of the special screw

clamps CL-GRP 300 [7-2] which are slid

into the receptacle slots provided (Figure

[7a]). This makes secure holding possible

also on uneven surfaces. In addition, the

“Anti-slip Coating” applied to the underside

of the guide rail ensures secure contact and

prevents scratches on sensitive material

surfaces.

Mounting the Connection Piece

(CN-GRP)

Depending on the application and the size

of the work piece, several guide rails can be

connected together (Figure [7c]) with the

use of the connection piece [7-4]. For the

permanent connection of several guide rails,

the connection pieces can be fastened with

screws at the respective threaded holes.

Mounting the Angle Unit (GRP-AG-2)

The combination of the guide rail and the

continuously adjustable angle unit [7-3]

makes possible exact angle cutting, e. g.,

for ﬁ tting work. The angle unit is mounted

according to Figure [7b]. On the scale, the

required angle can be set.

► When sawing with the PROTOOL GRP

guiding system, 4.5 mm is always to be

added to the necessary cutting depth.

Saw Table

Additional application possibilities are avail-

able with the use of a saw table. Further

information in this regard is available from

your dealer.

10 Maintenance

- The unit should be stored in a dry place

where it is protected against freezing.

WARNING

To verify that the protective insulation

remains intact, the machine must be

subjected to a technical safety test

afterwards. For this reason, this work

must be performed exclusively by a

professional electro-workshop.

- With each changing of the saw blade, re-

move deposited saw dust from the inside

of the protective guard.

- The ventilation slots on the motor casing

should be cleaned out from time to time.

After an operating period of approx. 200

hours, the following maintenance work

must be performed:

- Check the motor brushes and replace if

necessary. Clean the motor housing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool CSP 56-2 EB Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info