Bedienungsanleitung Protool CSP85-45 (Seite 19 von 134) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490702

Zoom out

Zoom in

Vorherige Seite

1/134

Nächste Seite

Non-ferrous Metals

Use only a suitable and sharp saw blade.

This ensures a clean cut and prevents jam-

ming of the saw blade.

Apply the machine running to the workpiece,

carefully start sawing and then saw with

slow feeding and without interruption.

For proﬁ les, always start the cut on the small

side; for U-proﬁ les, never start the cuts on

the open side.

Support long proﬁ le, otherwise the saw

blade can become jammed when the proﬁ le

tips over and the machine can “kick back”.

Connect the circular saw through a circuit

breaker to current protection (FI).

Connect suitable vacuum cleaner to the

tool.

Keep the tool clean off dust which accumu-

lates on the engine housing and inside the

protective cover.

Safety goggles should always be worn.

When large panels are cut, parafﬁ n should

be used as a lubricant. Thin-walled proﬁ le

sections upto 3 mm thick can be cut without

lubrication.

Material with Mineral Content

(Light building material)

► Only dry cutting is permitted.

► Use vacuum dust extraction. The vacu-

um cleaner must be suitable for masonry

dust.

9 Use of Accessories

The machine has a longitudinal slot at the

base plate underside to take up a guide rail.

With this guide rail, it is made easy to carry

out larger cuts.

PROTOOL Guiding System

For easy and safe handling when cutting

large work pieces as well as for achiev-

ing exact angle cuts, the use of the

GRP 800/1400/3000-2 guiding system is

recommended.

With it, clean cuts are possible by preci-

sion guiding of the machine along a cutting

line. In addition, the hard anodising of the

guide rail makes possible easy gliding of the

machine and thereby reduces the required

advancing force while improving the work

progress.

The guide rails are equipped with a splinter-

guard [4-1], which has to be cut to size

before the ﬁ rst use:

- Set the speed of the machine to level 6,

- Place the machine on the rear end of the

guide rail,

- Switch the machine on, press it down to

the set cutting depth and cut the splinter-

guard along the full length without inter-

ruption. The edge of the splinterguard

now corresponds exactly to the cutting

edge.

The saw’s side suction clearance is possible

to adjusting the adjusting nobs [3-11].

Mounting the Guide Rail

(GRP 800/1400/3000-2)

The mounting of the guide rail takes place

with the use of the special screw clamps

CL-GRP 300 [4-2] which are slid into the re-

ceptacle slots provided. This makes secure

holding possible also on uneven surfaces.

In addition, the “Anti-slip Coating” applied

to the underside of the guide rail ensures

secure contact and prevents scratches on

sensitive material surfaces.

Mounting the Connection Piece

(CN-GRP)

Depending on the application and the size

of the work piece, several guide rails can

be connected together with the use of the

connection piece. For the permanent con-

nection of several guide rails, the connec-

tion pieces can be fastened with screws at

the respective threaded holes.

Mounting the Angle Unit (GRP-AG-2)

The combination of the guide rail and the

continuously adjustable angle unit makes

possible exact angle cutting, e. g., for ﬁ t-

ting work. On the scale, the required angle

can be set.

► When sawing with the PROTOOL GRP

guiding system, 4.5 mm is always to be

added to the necessary cutting depth.

Saw Table

Additional application possibilities are avail-

able with the use of a saw table. Further

information in this regard is available from

your dealer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool CSP85-45 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info