Bedienungsanleitung Protool DWC 18-2500 DEC (Seite 19 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490654

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

9 Working instructions

► The auto feed attachment must not be

held in the depth stopper area as there

are moving parts!

► Each screw adjustment must be com-

pleted. Interrupted fastening or releasing

of the pressure during adjustment can

result in unsatisfactory machine function.

► The collated screws and the auto feed

attachment can only be replaced when

the power tool is turned off.

► Never use the auto feed attachment in

any other way than speciﬁ ed in this in-

struction manual.

► Use only original screwing bits.

► Use only original collated screws.

► Always store the collated screws in origi-

nal packaging.

► Always work in right angle against the

attached board.

Maintenance of the auto feed attach-

ment

The attachment generally does not require

any maintenance. After long period use, we

recommend to clean with pressurized air.

The auto feed attachment may be lubri-

cated in the area of the carriage guide (see

picture [12 b]).

Prior to cleaning, dismantle the attachment,

as speciﬁ ed above.

Prior to cleaning, remove the collated

screws from the attachment, as speciﬁ ed

in the point Removing the collated screws.

Pull the auto feed attachment from the dry-

wall screwdriver.

Disassembly of the slides

1. Push the depth stopper [9-2] into the

housing until the arresting button [12-1]

is at the level of the sign for dismantling

the slides [12-2] – see ﬁ gure [12 a].

2. Press the arresting button [12-1] and

concurrently remove the slides from the

holder – see ﬁ gure [12 b].

3. Press the orange button [9-1] and con-

currently release the depth stopper – see

ﬁ gure [12 c].

Transport lever disassembly

1. Press the button [13-1] and concurrently

pull it out– see ﬁ gure [13a].

2. Remove the released button [13-1] (ﬁ g-

ure [13 b]) with the transport lever [13-2]

and the spring [13-3] from the slides

(ﬁ gure [13 c]).

Clean individual parts, replace defective or

worn parts, and assemble in the opposite

sequence.

CAUTION

During reassembly of the transport

lever into the slides, pay due care to

correct ﬁ tting of the spring [13-3] in

the transport lever. Incorrect assem-

bly may result in dysfunction of the

belt transport.

Acoustic warning signal

Acoustic warning signals sound and the ma-

chine switches off in the following operating

states:

peep

- Battery ﬂ at or machine

overloaded

• Change the battery

pack.

• Place the machine under

reduced stress.

peep peep

- Machine is overheating

• You must allow the

machine to cool before

using again.

peep peep peep

- LiIon battery pack is

faulty or has overheated.

• Once the battery pack

has cooled, perform a

functional check using

the charger.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool DWC 18-2500 DEC Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info