Bedienungsanleitung Protool ISP 330 EB (Seite 24 von 182) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490698

Zoom out

Zoom in

Vorherige Seite

1/182

Nächste Seite

5.4 Emission levels

Levels determined in accordance with EN 60 745

are typically:

Sound pressure level L

= 92 dB (A)

Noise level L

= 103 dB (A)

Uncertainty K = 3 dB

Acoustic output value measured according to es-

tablished guideline 2000/14/EC, appendix VI.

= 103 dB (A)

WAd

= 105 dB (A)

Uncertainty K = 3 dB

Measurement was performed by notiﬁ ed individual

No. ES-1014 EZU s. p. Pod Lisem 129, 171 02

Prague 71.

CAUTION

Operating noise

Damage to hearing

► Use ear protection!

Vibration emission value a

(vector sum for three

directions) and uncertainty K measured in accord-

ance with EN 60 745:

= 3.4 m/s

Uncertainty K = 1.5 m/s

Declared total value of vibrations was measured

according to standard measure method and can

be used for comparison one powertools with the

others.

Declared total value of vibrations can be used for

preliminary setting of exposition.

Warning:

Emission of vibrations during real operating can

be different from declared total value of vibrations

depending on speciﬁ c real conditions.

To protect operating person shell be provide safety

measurement, that evaluate the exposition un-

der the real conditions (here are included all parts

of operating cycle, switch of mode and idle run

mode).

6 Transport and delivery

The ISP 330 EB insulation saw has been tested and

is delivered in perfect condition. The oil reservoir

of the machine ISP 330 EB is not ﬁ lled. When the

machine is delivered, take it directly out of the

packaging and check for potential damage during

transport. Any damage caused during transport

must be reported to the carrier immediately.

6.1 Storage

The packed insulation saw can be stored in a dry

storage area without a heating, where the tem-

perature does not drop bellow −5 °C. Store the un-

packed saw only in a dry closed storage where the

temperature does not drop below +5 °C, and where

sudden temperature changes are prevented.

7 Adjustment

CAUTION

All adjustments and settings must be carried out

before the machine is switched on.

WARNING

Danger of electrical injury.

Unplug any tool before handling.

Wear protective gloves!

7.1 Tilting the guide bar lengthwise

The guide bar, including the guard plate, can be

tilted 10° backward. This adjustment is mainly

used when multiple layers are cut at the same

time. It prevents resistance to the tool and an

uneven cut.

- Release lever [3-1] upward (Fig. [3a]).

- By pulling the handle, tilt the guide bar back-

wards and secure it again with the lever [3-1]

downward (Fig. [3b]).

7.2 Cutting angle adjustment

WARNING

For bevel cuts the maximum cutting depth is

limited.

Release the hand screws [4-2] on both sides. Us-

ing the bevel indicator [4-3], adjust the cutting

angle to the required value (the bevel indicator is

divided into 1° increments). Re-tighten the hand

screws [4-2].

7.3 Motor electronics

Starting current limitation

Smooth, electronically controlled starting ensures

that the machine starts without kickback. Due to

the machine’s limited starting current, a 16 A cir-

cuit breaker is sufﬁ cient.

Idle speed reduction

The electronics reduce the machine’s RPM during

idle, which also decreases wear to the motor and

gears.

Constant electronics

Constant electronics maintain the RPM the same at

idle and under load, which ensures uniform work

movement and a high-quality cut.

Electronic overload protection

If the machine is extremely overloaded, electronic

protection guards the motor from damage. In this

case, the motor stops and resumes only after dis-

charge, and after the switch is engaged again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool ISP 330 EB Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info