Bedienungsanleitung Protool MXP 1200 (Seite 13 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490693

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

- By pulling on the stirrer rod, you can pull the

ErgoFix adaptor [1-8] out of the machine spin-

dle. In this way, you can adjust ﬁ ve different

working heights. One step is 2 cm. The maxi-

mum adjustment movement is 8 cm and the

end position is signalled by reaching the groove

[2-2] on the ErgoFix adapter.

- Then release the clamping ring of the ErgoFix

adapter [1-7] and check that the adapter [1-8]

is seated securely in the machine spindle.

Quick change function

NOTE

Ensure that the adapter [1-8] remains

clean.

Do not lubricate the adaptor [1-8].

Only press the ErgoFix casing [1-7] when

the machine is not in operation.

The ErgoFix interface enables you to easily and

quickly remove the stirrer rod from the machine.

- Push the clamping ring of the ErgoFix adapter

[1-7] in the direction of the machine to move it

as far as it goes and hold it tight.

- By pulling on the stirrer rod, you can pull the

ErgoFix adaptor [1-8] completely out of the ma-

chine spindle.

Changing the stirrer

► Adapter ErgoFix [2-1] after worn-out of stirrer

rod can be reused.

Set the wrench [2-3] on the hexagon of the stirrer

endpiece [2-4] and turn to the left to screw the

stirrer rod out of the ErgoFix adapter [2-1].

6.6 Stirrer

To mix different material mixtures together, use

different PROTOOL stirrers: see the catalogue

PJ Uni

For wall paints,

emulsion paints,

ready-made ﬁ ller,

ready-mix plaster,

varnishes/glazes

For wall paints,

emulsion paints,

pastes, varnishes

casting compounds,

bitumen, sludges

HS2

For tile adhesives,

joint sealant, adhe-

sive mortar, ready-mix

plaster, screed, ﬁ llers,

levelling compounds

HS3R

For mortar, concrete,

cement and lime

plaster adhesive ﬁ ller,

screed, quartz-ﬁ lled

epoxy resin, thick

bitumen coating

HS3L

For gypsum plaster,

emulsion paints,

varnishes wall paints,

casting compounds

For paints, varnishes,

wall paints, emulsion

paints, plasters, glues,

tile adhesives

For balancing weights,

ﬁ llers, sealants,

adhesives

6.7 Mains connection

WARNING

There is a risk of accidents occurring if you

do not use the correct power supply.

The stirrer must only be operated with a single-

phase alternating current with a nominal voltage of

220–240 V/50–60 Hz. In the 2nd level, the machine

is protected against accidents caused by electrical

current in accordance with the standard EN 60 745-1

and it has built-in radio interference suppression in

accordance with the standard EN 55 014.

Before starting up the machine, check that the

speciﬁ cations on the type plate correspond to the

actual voltage of the power supply.

If required, you can extend the ﬂ exible power cable

as follows:

- Length 20 m, conductor cross-section

3×1.5 mm

- Length 50 m, conductor cross-section

3×2.5 mm

Only use extension cables that are suitable for

outside use and that are marked accordingly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool MXP 1200 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info