Bedienungsanleitung Protool PLP 205 (Seite 11 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490710

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Cutting blades

Dust extraction

Lateral guide roller

- Connection to a standby unit or generator:

minimum power 5 kVA / 230 V, 50 Hz.

There must be no metal particles on the

surface of the workpiece to be planed.

- For secure guidance, the planer is equipped

with two handles. Planing depth is adjustable

by means of the swiveling front handle (5) and

the pointer on the handle (6) points at the

value of adjusted planing depth. The adjusted

value may be fixed by means of the pivoted

locking lever (7).

- The incorporated soft-start/brake electronic

circuit “SSB electronic” provides for soft

starting when the electric tool is switched on,

as well as short rundown time of approx. 4 s

when the electric tool is switched off.

- When working with the planer, place the front

adjustable shoe (8) onto the workpiece and

switch the motor on, using the switch (2) with

the lock-off button (3) depressed

simultaneously. As soon as the cutting head

comes in contact with the workpiece, guide

the planer with constant feed speed, applying

light pressure.

- When planing for a long time with the

maximum planing depth 3 mm adjusted and

maximum planing width utilized, the LED

overload indicator (4) is to be observed to

make sure that the electric tool is not

overloaded – the LED light intensity increases

with overload and the cut-out is triggered after

certain overload rate is achieved. The electric

tool can be started again only after the mains

switch (2) has been released and pressed

again.

(Figures 1 and 3)

When the maximum planing width is to be

utilized, there is possible to lift the pivoted guide

roller (10) into the working position. After the

work is finished, tilt the guide roller back into the

parking position.

When working with wood for a long period or for

industrial use with materials which produce

harmful dust, this electric power tool must be

connected to a suitable external dust extraction

device - connection tube diameter 57,5 mm.

The cutting head (15) is fitted with the reversible

blades (16) which cannot be resharpened but

may be reversed once. Blunt blades reduce

quality of the work and increase the risk of

kickback. Therefore they must be turned or

replaced in good time.

The following instructions must be followed

exactly.

- Pull the plug from the mains socket.

- Lock the cutting head against rotation (insert a

pin into the hole (19)).

- Loosen the fixing screws (20) and pull out the

blade (16) together with the backing plate (17)

sideways.

- Remove the clamping rail (18) upwards.

- Clean the backing faces.

- Replace the clamping rail (18) from above

back in the original position.

- Place the blade (16) to the backing plate (17)

and push both parts back sideways into the

cutting head (15), observing correct position

according to the illustration.

- Move the blade laterally, such as its side edge

is aligned with edges of the adjustable and

fixed shoes of the planer.

- Press the blade attachment system down

(using a piece of wood or gloves) and slightly

tighten the fixing screws (20), starting from

center of the cutting head, then tighten the

screws with the torque of 8,5 Nm.

Mounting position of the blade attachment

system has been pre-adjusted in the factory,

therefore no height alignment of blades to the

cutting circle is necessary.

Blade replacement

Removing the blade

Fitting the blade

(Figure 4)

(Figure 6)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool PLP 205 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info