Bedienungsanleitung Protool PLP 205 (Seite 12 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490710

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Noise/vibration information

Guarantee

Repairs and servicing

Recycling

After their service life is ended, submit the

electric tool, its accessories and packages to a

disposal premise to allow reusing of the raw

materials.

To allow material-sorted recycling, all plastic

components are marked with relevant symbols.

Maintenance and care

Storage

Lift-off carbon brushes

- The carpentry planer requires practically no

maintenance.

- Lubrication for the antifriction bearings is

designed to last for the service life of the

electric tool.

- However, it is recommended to remove

accumulated dust and chips regularly by

blowing compressed air through the motor

ventilation holes while the motor is running.

- The guide faces are to be kept clean from

resins and similar deposits.

- When working under extreme conditions, e.g.

planing wood with high contents of resins or

moisture, deposits accumulated inside the

electric tool can reduce effectiveness of dust

and chip extraction.

- Remove plug from the mains socket before

opening the housing cover (13).

- Cleaning, if necessary, may be carried out

after removing of the housing cover – loosen

the hexagon-head screw (25) using the

wrench (21).

- After the interior of electric tool has been

cleaned, replace the cover and tighten the

screw again.

Important:

The carbon brushes are specially designed to

allow their wear only to the minimum usable

length. Then the power supply circuit is

automatically interrupted and the electric tool

stops running.

Replacement of the carbon brushes is to be

carried out by specialized service personnel

only.

Packed electric tools may be stored in dry

unheated storerooms with temperatures not

dropping below - 5°C. Unpacked electric tools

shall be stored only in dry self-contained

storerooms with temperatures not dropping

below + 5°C, where sudden temperature

changes are prevented.

(Figure 1)

Repairs in the warranty and post-warranty

periods are carried out by the servicing

workshops listed in the index of addresses.

We guarantee PROTOOL appliances in

accordance with statutory/country-specific

regulations (proof of purchase by invoice or

delivery note).

Damage attributable to normal wear and tear,

overload or improper handling will be excluded

from the guarantee.

In case of compliant please send the machine,

undismantled, to your dealer or the Service

Centre for electric power tools.

Noise and vibration levels measured and

determined according to EN 50144.

The typical A-weighted noise levels of the

electric tool are:

Sound pressure level: 96 dB(A)

Sound power level: 109 dB(A)

The typical level of hand-arm vibration is less

than

Sound pressure level: 92 dB(A)

Sound power level: 105 dB(A)

The typical level of hand-arm vibration is less

than

PLP 205:

Use ear protection!

PLP 245:

Use ear protection!

2,5 m/s .

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool PLP 205 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info