Bedienungsanleitung Protool VCP 260 E L (Seite 19 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

70266

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

8 Working

8.1 AUTOClean - Cleaning the

main ﬁ lter

To maintain a constant suction power when

extracting ﬁ ne dust, you can adjust the

frequency of the automatic [1-7] cleaning

system in inﬁ nite variables using the rotary

knob. Always use the automatic cleaning

system in combination with a disposal bag

(in line with dust class ‘M’ requirements).

Always use a ﬁ lter bag when the cleaning

function is switched off (except for when

wet vacuuming).

Before performing wet extraction

tasks or working with a ﬁ lter bag, set

the rotary knob to position 0.

For large amounts of dust, optimum opera-

tion is only possible if dedusting is switched

on.

Manual cleaning

If the suction power decreases, clean-

ing can be started manually by turn-

ing the switch [1-9] to the AC symbol

positioned on either side of the switch.

We recommend cleaning the main ﬁ lter

completely if severely clogged:

Set the suction power adjuster [1-8] to the

maximum setting.

Cover the end of the nozzle or suction hose

with your hand for 10 seconds.

Turn the switch to the [1-9] AC symbol.

In intensive applications that generate ad-

herent dust, it may be necessary to clean

the ﬁ lter element mechanically under cer-

tain circumstances (extract). Wear a dust

mask!

8.2 Extracting dry materials

CAUTION

Hazardous dust

Damage to the respiratory passage

Use a ﬁ lter or disposal bag when extract-

ing hazardous materials!

Do not use the machine if the volumetric

ﬂ ow monitoring function is inactive.

Observe the following when extracting

dust generated by operating electric power

tools:

If the exhaust air is discharged back into

the room, the air renewal rate L within

the room must be sufﬁ cient. The volume of

air discharged back into the room must not

exceed 50% of the fresh air volume ﬂ ow

(room volume V

x air renewal rate L

Observe all the relevant regional regula-

tions.

Remember: A moist main filter clogs

more quickly when extracting dry materi-

als. Therefore, dry the main ﬁ lter before

extracting dust or replace the damp ﬁ lter

with a dry one.

7.8 Volumetric ﬂ ow monitoring

An acoustic warning signal sounds if the air speed in the suction hose falls below 20 m/s

(for dust class M only).

Possible causes Solution

Value set on the suction power adjuster

[1-8] is too low.

Set the suction power adjuster to a higher

value (see Chapter 7.3).

The rotary knob [1-10] is not set to the

hose diameter setting (only for dust

class M).

Set the correct hose diameter.

Suction hose blocked or kinked. Remove blockage or kink.

Filter bag/disposal bag full. Insert a new ﬁ lter bag (see Chapter 7.6).

Filter element clogged. Clean ﬁ lter element (see Chapter 8.1).

Change the ﬁ lter element (see Chapter 9.1).

Monitoring electronics malfunction. Send to a PROTOOL service workshop for

repair.

Wet extraction. Functional reliability not affected, no

actions required.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool VCP 260 E L Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info