Bedienungsanleitung Proxxon DSH-E (Seite 8 von 20) (Englisch)

782198

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

- 8 -

IMPORTANT

Additional Safety Instructions For Scroll Saws

Your safety is very important! Please follow the warnings

below :

3. Additional Safety Instructions For Scroll Saws

Safety is a combination of common sense, staying alert and

knowing how your scroll saw works. Read this manual to

understand this saw and become familiar with its contents,

including all the safety warnings. Do not allow familiarity

(gained from frequent use of your Scroll Saw) to become

commonplace. Always remember that a careless fraction of a

second is sufficient to inflict severe injury.

Developing these habits in your shop and safety will become

second nature to you.

ALWAYS WEAR EYE PROTECTION

Projectiles thrown away from the machine could cause serious

permanent eye damage. Always wear safety goggles, not

glasses, complying with ANSI Z87.1 (or in Canada CSAZ94-3-

M88). Everyday eyeglasses have only impact resistant lenses.

They are not safety glasses! Safety goggles are available at

many local retail stores. Glasses or goggles not in compliance

with ANSI or CSAcould seriously hurt you when they break.

DO NOT REMOVE JAMMED CUTOFF PIECES UNTIL

BLADE HAS STOPPED1

Before freeing any jammed material or loose pieces from the

saw table, turn the machine off, wait for all moving parts to

stop and unplug the saw!

MAINTAIN PROPER ADJUSTMENT OF BLADE TENSION

AND BLADE GUARDS

Quick Release Tension Lever should be in the correct position

before operating. Make sure the blade tension is properly

adjusted: For finely setting the correct saw blade tension you

can use the knob on the upper back part of the housing,

observe the instruction manual!

HOLD WORK PIECE FIRMLYAGAINST TABLE

Plan the way you will hold the work piece from start to finish;

and follow the instructions:

Reduce the Risk of awkward operations and hand positions

where a sudden slip could cause fingers or hand to move into

the blade. Keep your face and body to one side of the blade, out

of line with a possible thrown piece if the blade should break.

Always use extra caution with large, very small or awkward

work pieces! Do not use this Scroll Saw to finish pieces too

small to hold by hand, and, if necessary, use extra supports

(saw horses, V-blocks, tables, etc.) for any work pieces large

enough to tip when not held down to the table top.

• Support round material such as tubing or dowel rods. They

have a tendency to roll during a cut, causing the blade to

“bite”. To avoid this, always use “V” blocks.

• When cutting irregularly shaped work pieces, plan your work

so it will not pinch the blade. Apiece of molding, for example,

must lay flat or be held by a fixture or jig that will not let it

twist, rock or slip while being cut.

• Cut only one work piece at a time.

• Clear everything except the work piece and related support

devices off the table before turning the saw on.

Never turn your Scroll Saw on before clearing the table of all

objects (tools, scraps of wood, etc.) except for the work piece

and related feed or support devices for the operation planned.

Do not use another person as a substitute for a table

extension, or as additional support for a work piece or to help

feed, support or pull the work piece.

INSTALL BLADE TEETH POINTING DOWN TOWARDS

TABLE

The Scroll Saw should cut on the down stroke. Always make

sure blade teeth are oriented downward toward table.

KEEP FINGERS IN ASAFE DISTANCE FROM THE BLADE

Do not cut pieces so small that your fingers go under the

blade guard. Never reach in blade cutting path with your

hands or fingers.

Use jigs or fixtures to hold the work and keep your hands

away from the blade.

When making a very small cut out, always secure the work

piece to a scrap piece of plywood with double faced tape. This

way, the work is supported and your fingers are away from the

blade.

BLADE GUARD/HOLD DOWN MUST CONTACT

WORKPIECE

Never use your Scroll Saw with the blade guard removed,

damaged or mounted incorrect (see instruction manual). A

blade guard that is damaged should be properly replaced.

NEVER LEAVE SCROLL SAW WITH MOTOR OPERATING

Never leave the Scroll Saw running unattended. Turn the saw

OFF, make sure the saw has come to a complete stop, and

then remove plug from power supply before leaving the work

area.

ADJUST BLADE TENSIN BY HAND. NO TOOLS

For finely setting the correct saw blade tension you can use

the knob on the upper back part of the housing, observe the

instruction manual! Do not use any tools!

RAISE GUARD/HOLD DOWN WHEN TILTING TABLE

SECURE TOOLPROPERLY TO PREVENT UNEXPECTED

MOVEMENT

Bolt the saw on a firm level surface where there is plenty of

room for handling and properly supporting the work piece, like

a stable, level table, workbench or the floor. The saw may

move when cutting large work pieces if not secured (See also

“Setting up the saw” in the manual). Support large work pieces

Proxxon_BedienAnl_DSH_US_Bel 10.06.2005 14:20 Uhr Seite 8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proxxon DSH-E Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Proxxon DSH-E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info