Bedienungsanleitung Proxxon FF 230 (Seite 9 von 16) (Englisch)

782209

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

-9-

1. Securely fasten the work piece using clamps,in a vice,

or to the support of the lathe chuck. Alternatively, you

canclamp the work piece in amachine viceand mount

the vice on the work table using the T-grooves.

2.Adjust desired milling depth.

3.Tighten clamping screws 3 and 4 (Fig. 9).

4. Ensure that the milling tool does not touch the work

piece.

5. Ensure that the proper spindle speed has been adjusted.

6.Switch on milling machine at switch 3 (Fig. 1).

7.Work using a suitable feed

Note:

The feed must always take placeagainst the cutting

direction of the milling cutter (also refer Fig.14.)

Impor tant!

Always provide feed by hand only!When using the milling

machine in conjunction with the lathe PD 230/E, feed action

must not occur via the lathe's automaticfeed. Risk of injury!

Repair and maintenance

Impor tant:

Disconnect mains power beforecleaning and maintaining

unit.

Do not usecompressed air when cleaning.

Setting compound-type table guide play

If, after a time, the compound-type table guide is found to

have too much or too little play, the play canbe reset using

the adjusting screws 2 (Fig. 15). For this purpose,loosen

adjustment screw lock nuts 1and screw in all adjustment

screws evenly until play is eliminated. Retighten lock nuts

afterwards.

Setting compound-type table spindle play

If play of the spindles increases, release the nut 1 using a

socket spanner 2 or i. e. a ratchet. (Fig. 16)approx. one half

turn. Then turn the hand wheel to the right hand direction

until the play has been eliminated. Now retighten the nut 1

firmly, while holding the handwheel in the position it has

been adjusted.

Note:

See exploded view,page 10: Where necessary,play in the

individual spindle threads canalsobeachieved by slightly

tightening the spindle nut, Item 3, with the bolt, Item 25.

W arning

Toavoid fire or toxic reaction,never use gasoline,naphtha,

acetone,lacquer thinner,or similar highly volatile solvents to

clean the Milling machine.

Do not allow brake fluids,gasoline,or penetrating oils to

come in contact with the plasticparts.They contain

chemicals that can damage or destroy plastics.

Turn switchOFF and always remove plug from power

sourcebefore making any adjustments or repairs.

All electrical or mechanical repairs should be done only by

qualified service technicians.

When servicing use only PROXXON replacement parts.Use

of any other parts may createahazard or cause product

damage.

Any attempt to repair or replace electrical parts on this lathe

may createahazard unless repair is done by aqualified

service technician. Repair service is available at your

PROXXON servicecenter (You find the address at address

at the back of this manual)

Lubricating the machine

To ensurealong service life of your machine,please

observe the lubrication diagram in Fig. 17 (A: Lubricate

each time before use / B: Lubricate onceamonth). Only

useacid-free machine oil for lubrication.

Only useacid-free machine oil.

Replacement of the belts

Important:

Use only accessories recommended for this lathe. Follow

the instructions that accompany accessories.Use of

improper accessories may cause hazards.

If the belts become worn, you canchange them yourself.

Replacement belts areavailable from the PROXXON central

service team (address on the rear side of these

instructions).

•Unscrew screw 5 (Fig.13) to release the belt pulley 1.

•Unscrew the 3 screws 6 (Fig.13)and lift out the motor.

•You can now removeand replace the belts.

•Re-assemble in reverse order.

After use

Attention:

Disconnect milling machine mains plugbeforecleaning!

Cleancompound-type table and milling machine using a

soft clothand brushafter use. Then lightly oil the guides

and distribute the oil by moving the table. Never use

compressed air for cleaning the compound-type table as

cuttings entering the guides in this manner could destroy

the guides.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proxxon FF 230 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info