Bedienungsanleitung Proxxon FF 230 (Seite 7 von 16) (Englisch)

782209

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

- 7 -

General view, KT 230 compound-type table (Fig. 2)

1. Handwheel for Xdirection (170 mm travel)

2.Scale ring

3.Work table (270 mm x 80 mm)

4. Table mounting hole

5. Pedestal

6.Handwheel for Ydirection (60 mm travel)

7.Support

8. Clamping screw

9. Scale

10.Pillar clamping screw

11. T-grooves

The PROXXON PF 230 milling machine may be used in

conjunction witha compound-type table or the PROXXON

PD 230/Elathe (in the latter case, the lathe support is used

in place of the compound-type table).

Technical data

PF 230 milling machine technical data

Voltage:115 Volt, 60Hz

Power rating:140 Watt

Short-term operation 10 min.

6 spindle revolutions by re-positioning the belt:

280,540, 780,910,1710 and 2500/rpm

Sleevestroke 30 mm (1 6 / 32”)

Verticaladjusting displacement200 mm (7 14/ 16 ”)

Generated noise≤70 dB(A)

Vibrations≤2.5 m/s2

Dimensions:refer toFig. 3

Weightapprox. 7.5 kg (16.5 lb)

Only for operation in closed rooms.

KT 230 compound-type table technical data

Workarea: 270 mm x 80 mm

Adjustment travel in Xdirection:170 mm

(10 5 / 8 ” x 3 5 / 32”)

Adjustment travel in Ydirection: 60 mm (2 3 / 8 ”)

Weight:9.5 kg (21 lb)

Dimensions of T-grooves: refer toFig. 4

Groove spacing: 25 mm (1”)

Feed per rotation:1.5 mm (1 / 16 ”)

Feed per graduation line: 0.05mm(3 / 64 ”)

Assembly of the milling machine

W arning:

Toavoid injury from unexpected starting or electrical shock,

do not plug the power cord intoapower source receptacle

during unpacking and assembly.This cord must remain

unplugged whenever you are working on the milling

machine.

W arning:

Ifany part is missing or damaged,do not plug the milling

machine in until the missing or damaged part is replaced,

and assembly is complete. Toavoid electrical shock, use

only identical replacement parts when servicing grounded

tools.

W arning:

For your safety,never connect the plug to the power source

receptacle until the assembly and adjustment steps are

completed, and you have readand understood the safety

and operating instructions.

Mounting on lathe PD 230/E

1. Mounting lathe on afirmbase.

2.Attach the mounting block 1 (Fig. 5) to the lathe 3, using

screws 2 (Do not tighten screws yet!)

3.Tighten screw 3 (Fig. 6)and insert pillar 1.

4. Tighten screw 4 toclamp the pillar.

5. Attach the milling table 3 (Fig. 7) to the lathe support

using screws 2 and square nuts 1.

Mounting of milling machine on KT 230 compound-type

table

Note:

Safe and precise operation is only possible if the machine is

properly fastened toa stable work surface.

1. Attachcompound-type table to work surface using 4

screws 1(i.e. M4,not included,look at Fig. 8).

2.Insert pillar in flange and clamp using screws 2.

W arning:

For your own safety,do not plug the tool into the power

source receptacle, until the parts arecorrectly installed and

adjustments havebeen made.

Impor tant!

Toavoid injury from accidental start,make sure the switch

is in the OFF position and the plug is not connected to the

power source receptacle beforechanging any parts or tools

(i. e. cutter)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proxxon FF 230 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info