Bedienungsanleitung Proxxon LHW (Seite 11 von 78) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch)

782216

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

- 11 -

dust generated during the operation. If you are ex-

posed to loud noise for a long time, you may suffer

hearing loss.

i) Keep other people at a safe distance away from

your work area. Anyone who enters the working

area must wear personal protective equipment.

Fragments of the work piece or broken bits and cut-

ters can fly away and cause injuries even beyond the

immediate area of work.

j) Hold the device only by its insulated grip surfaces

if you perform work where the bits and cutters

could contact hidden power cables or your own

mains cable. Contact with a live cable can energize

metal device parts and cause electric shock.

k) Keep the mains cable away from rotating bits and

cutters. If you lose control of the device, the mains

cable could be cut or snagged, and your hand or

your arm could get pulled into the rotating bits and

cutters.

l) Never set down the power tool until the bits and

cutters come to a complete stop. Turning bits and

cutters grab the depositing surface and pull the

power tool out of your control.

m) Do not allow the power tool to run while you are

carrying it. Your clothing could get snagged acci-

dentally in the rotating bits and cutters, causing the

power tool to pierce your body.

n) Regularly clean the ventilation slits of your power

tool. The motor fan sucks dust into the housing and

a strong accumulation of metal dust can cause elec-

trical hazards.

o) Do not use the power tool in the vicinity of com-

bustible materials. Sparks could ignite these ma-

terials.

p) Do not use bits and cutters that require liquid

coolants. The use of water or other liquid coolants

can cause electric shock.

Additional safety guidelines on grinding and abrasive

cutting.

a) Special safety guidelines on grinding and abra-

sive cutting:

b) Use only the grinding tools approved for your

power tool and the protective guard designed for

these grinding tools. Grinding tools that are not

designated for the power tool cannot be adequately

guarded and are therefore unsafe.

The protective guard must be attached securely to

the power tool and adjusted in such a way as to

achieve maximum safety, i.e. the smallest possible

part of the grinding tool is open to the operator. The

protective guard is meant to protect the operator from

fragments and accidental contact with the grinding

tool.

d) Grinding tools may only be used for the recom-

mended applications. For example: Never grind

with the lateral surface of a cutting disc. Cutting

discs are intended for removing material with the

edge of the disc. Lateral forces on these grinding

tools can shatter them.

e) Always use undamaged clamping flanges in the

correct size and shape for your selected sanding

disc. Suitable flanges support the sanding disc and

reduce the danger of sanding disc breakage.

Flanges for cutting discs can differ from other sand-

ing disc flanges.

f) Do not use worn sanding discs from larger power

tools. Sanding discs for larger power tools are not

designed for higher rotational speeds of smaller

power tools and can shatter.

Further special safety guidelines on abrasive cutting:

a) Avoid jamming the cutting disc or applying too

great contact pressure. Do not make excessively

deep cuts. Overstressing the cutting disc increases

its load and its susceptibility to twisting or jamming

and thus the possibility of recoil or grinding tool

breakage.

b) Avoid the area in front of and behind the rotating

cutting disc. If you move the cutting disc in the

work piece away from you, recoil may catapult the

power tool with the rotating disc directly towards

you.

c) If the cutting disc binds or if you interrupt work,

switch off the device and hold it still until the disc

has come to a complete stop. Never attempt to

pull the running cutting disc out of the cut, other-

wise recoil may occur. Determine and eliminate the

cause for binding.

d) Do not switch the power tool back on as long as it

is in the work piece. Allow the cutting disc to

reach its full rotational speed before carefully

continuing the cut. Otherwise, the disc can get

snagged, jump out of the work piece or cause recoil.

e) Support sheets or large work pieces to minimize

the risk of recoil caused by a jammed cutting disc.

Large work pieces can sag under their own weight.

The work piece must be supported on both sides of

the disc; namely near the separating cut as well as

at the edge.

f) Be especially careful when making “pocket cuts”

in existing walls or other blind areas. The dipping

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proxxon LHW Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info