Bedienungsanleitung Pulsar Apex XD38 (Seite 10 von 55) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

572608

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

16 17

TECHNICAL INSPECTION

It is recommended that you inspect the sight before every use. Make sure to

check for the following:

џ Visually inspect that the unit is free from any physical damage; cracks, dents

or signs of corrosion which may disqualify it from proper use.

џ Check the sturdiness and proper fit of the mounting system.

џ Ensure that the objective lens and eyepiece are free of cracks, grease spots,

dirt, water stains and other residue before use.

џ Visually inspect the condition of the battery and the battery compartment; the

battery should be free of electrolyte and oxidation residue, especially where

the battery makes contact with metal.

џ Verify the proper function of the following: selector switch, display brightness

adjustment knob and other operation buttons.

џ Verify the smoothness of the objective lens focus knob, dioptre focus knob.

TECHNICAL MAINTENANCE

Technical maintenance should be done at least twice a year, includes the

following steps:

џ Clean the outside metal and plastic surfaces from dust, dirt and moisture;

wipe the scope with a soft lint free cloth.

џ Clean the battery compartment's electric contact points using an oil-free

solvent.

џ Inspect the eyepiece lens and the objective lens and gently blow off any dust

and sand, and clean using lens cleaner and a soft cloth; see section 6

“GUIDELINES FOR OPERATION”.

STORAGE

Always store the unit in its carrying case in a dry, well-ventilated space. For

prolonged storage, remove the batteries.

TROUBLESHOOTING

Listed below are some potential problems that may occur when using the

scope. Carry out the recommended checks and troubleshooting steps in the

order listed. Please note that the table does not list all of the possible problems.

If the problem experienced with the scope is not listed, or if the suggested

action meant to correct it does not resolve the problem, please contact the

manufacturer.

CORRECTIVE ACTION

Reinstall the batteries observing

polarity.

Clean the battery compartment,

focusing on the contacts.

Install fresh batteries. Use spare

battery container.

Do the calibration according to

section 9 “OPERATION”.

Adjust brightness by rotating the

controller (9).

If you wear prescription glasses

with a range of +/- 4, keep glasses

on when looking through the

eyepiece.

Clean the lens surfaces with a

blower and soft lens cloth.

Let the sight dry by leaving it in a

warm environment for 4 hours.

Adjust the image by rotating the

lens knob (6).

Check that the sight has been

securely mounted, make sure that

the same type and calibre bullets

are being used as when the scope

was initially zeroed; if your sight

was zeroed during the summer,

and is now being used in the

winter (or the other way round), a

small displacement of the aiming

point is possible.

Adjust the sight according to the

instructions given in the Section 9

“OPERATION” and check the

surfaces of the eyepiece and

objective lenses and clean them if

necessary from dust,

condensation, frost, etc; to prevent

fogging in cold weather, apply a

special anti-fog solution.

Check focusing of the scope in

night conditions.

Activate the remote according to

instructions in section 13.

Install a new CR2032 battery.

POSSIBLE CAUSE

Batteries have been incorrectly

installed.

Oxidized contact points in the

battery compartment due to “leaky”

batteries or contact points

becoming exposed to a chemically

reactive solution.

The batteries are fully exhausted

or one or several batteries are

faulty.

Calibration is to be done.

The lowest brightness level is set.

The dioptre cannot be adjusted to

your eyesight.

Dust and condensate are covering

the outside optical surfaces after

the sight was brought in from the

cold into a warm environment, for

example.

The objective lens is not focused.

The sight is not mounted securely

or the mount was not fixed with

thread sealant.

Wrong settings.

The scope is used in day light at

long working distance.

Remote control is not activated.

Low battery.

Make sure your power supply

provides output voltage. Make

sure the central pin of the external

power supply (15) and plug

contacts (13) are intact.

PROBLEM

The sight will not turn on.

The image is blurry, with vertical

stripes and uneven background.

The image is too dark.

The reticle is blurred and cannot

be focused with the dioptre knob.

With a crisp image of the reticle,

the image of the observed target

that is at least 30 m away is

blurred.

The aiming point shifts after firing

rounds. The sight will not focus.

The sight will not focus.

The sight cannot be started with

wireless remote control.

The unit does not operate on

external power supply.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pulsar Apex XD38 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info