Bedienungsanleitung Pulsar Apex XD38 (Seite 9 von 55) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

572608

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

Defective pixel repair

џ When operating the thermal imager, there is a possibility of defective (dead)

pixels (bright or dark dots with constant brightness) appearing on the

detector which are visible on the image.

џ Thermal sights Apex provide an opportunity to repair defective pixels on the

detector using a software-based method.

џ Press and hold the controller (9) for two seconds to enter the menu.

џ Rotate the controller to select icon and press the controller.

џ Select icon in the pop-up submenu and press the controller.

џ A cross appears in the centre of display, coordinates (X;Y) of the

cross relative to the centre of display appear in the place of pop-up icons,

icons disappear.

џ Rotate the controller to align the cross with a defective pixel (if the alignment

is correct, the defective pixel should go out).

џ Switch direction of the cross from horizontal to vertical by a short press of the

controller.

џ After the centre of the cross is aligned with a defective pixel, press the MODE

(3) button to repair the pixel.

џ In case of success a short “OK” message appears in the place of the

coordinates.

џ Further on, move the cross to repair another defective pixel. When moving

the cross to the coordinates area, the latter goes to the lower right portion of

the display.

Return to default defective pixel pattern

џ If you wish to return to the default defective pixel pattern (i.e. restore all

defective pixels previously repaired), select icon in the pop-up submenu

and press the controller.

џ Options “Yes” and “No” appear on the right of the icon.

џ Rotate the controller to select “Yes” and press the controller.

џ If you choose not to return to default pixel pattern, select “No” and press the

controller.

џ To exit the main menu, keep the controller pressed for two seconds or wait 10

seconds to exit automatically.

Attention! One or two pixels in the form of bright white or black 1-2 pixels dots

are allowed on the display of thermal imager. These pixels cannot be repaired

and are not a defect.

Restore of default settings

To return to default settings:

џ Rotate the controller to select “Default settings”. Press the controller button.

џ To activate return to default settings, rotate the controller to select “Yes”,

press the controller button.

The following settings will return to their original status before the changes:

Operation mode – “Rocks”;

Calibration mode – automatic;

Weapon selection – 1;

Selection of preloaded reticle – 1 (for all weapon types);

Reticle colour – black;

Brightness of onscreen symbols (menu and status bar) – 5;

Video output – off;

Display brightness level – 12;

Display contrast level – 12;

Digital zoom – x1;

Image inversion – off;

Function “PiP” – off

To cancel return to default settings, select “No” and press controller button to

confirm.

Note: zeroing coordinates do not return to default for all types of weapon.

VIDEO OUTPUT

Video output is designed to connect external recording devices and to

transmit video signal to monitors, TV sets etc.

џ Connect the plug (13) of the cable to the jack (10) of the sight by matching

the notch in the plug connector and the protrusion of the jack (10) (see the

scheme).

џ Secure the cable by turning clockwise the locking ring of the plug (13).

џ Connect the signal receiver to the jack (14) of the cable.

џ Turn on the sight – image will appear on the external device. Please make

sure the external device is in the AV mode.

џ To record video, you can use video recorders such as Yukon MPR

(#27041) / CVR640 (#17044) and others.

Note: it is not recommended to attach the CVR640 on the sight because the

video recorder is not designed for heavy shock resistance.

WIRELESS REMOTE CONTROL

The wireless remote control duplicates functions of the sight, calibration

function and digital zoom/PiP function.

It has three buttons:

џ Button “ON” (16) – turning the sight on/off (press for two seconds to

deactivate).

џ Button “CAL” (17) – image calibration.

џ Button “ZOOM/PiP” (18) – digital zoom on/off or function “PiP” on/off.

To start using the wireless remote control you will need to activate it:

џ Turn on the scope and select menu option “RC activation” (icon ).

џ Press controller button, a message “WAIT” will show up and countdown

will start within which you need to press any button of the RC.

џ If the activation is successful, a message “Complete” will show up next to

icon. The RC is ready for use.

џ If the RC does not work, replace the battery. To do this, unscrew the screws

on the rear panel of the RC, remove the cover, pull out the old battery and

insert a new CR2032 battery.

WEAVER RAIL 7/8“

With the help of the Weaver rail (11) you can attach accessories such as:

џ External power supply EPS3 (#79111).

14 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pulsar Apex XD38 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info