Bedienungsanleitung Pulsar DIGISIGHT N770A (Seite 6 von 44) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

621720

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Installation of mount

Before using the riflescope you need to install the mount.

The riflescope can be used with various mount types such as Weaver, Euro-

prism, Los, Side mount, MAK adapter etc. that allow the scope to be installed

on different types of rifles.

The mounting holes in the base of the riflescope enable the mount to be

installed in one of the multiple positions. The choice of the mounting position

helps the user to ensure the correct eye relief depending on the rifle type.

Attach the mount to the base of the riflescope using a hex-nut wrench and

screws (see installation scheme on page 5).

Install the scope on the rifle and check if the position is suitable for you;

If you are happy with its position, remove the scope, unscrew the screws

halfway, apply some thread sealant onto the thread of the screws and

tighten them fully (do not overtighten). Let the sealant dry for a while.

The riflescope is ready to be installed on a rifle and to be zeroed.

The riflescope can be powered with an external DC power supply (2.1mm pin)

with stabilised voltage ranging from 9V to 15V (max. consumption power 3W)

or a 12V vehicle socket.

External power supply (AC/DC) is to be connected to “Power” (13) jack

located on the right side of the device.

Note: the central pin of the power supply that you connect to the “power” jack

of the riflescope, must have marking “+”.

The power supply may have marking

Connection of an external power supply (icon on the data panel)

automatically cuts off power supply from batteries.

External power supply DOES NOT charge the batteries in the riflescope!

Attention! We suggest that you use battery packs EPS3 or EPS5

ensuring from 9 to 20 hours of continuous operation.

Warning! Focusing range may vary depending on the illuminance

level in the daytime mark “100 m” on the lens focus knob equates to

around 10 metres.

To increase 4.5x magnification up to 6.8x, activate 1.5x digital zoom by

pushing “SCR” (19) button.

In low light conditions or in complete darkness turn on the built-in laser IR

Illuminator (18). The IR Illuminator has three power degrees – choose the

required one by turning the selector switch (3) to one of the three positions

When finished, turn off the riflescope by turning the selector switch (3) to

the “OFF” position.

Close the lens cap (2).

Install the batteries according to the directions in Section 7 or connect an

external power supply.

Open the lens cap (2).

Turn on the riflescope turning the selector switch (3) to the “ON” position –

within a couple of seconds the display will light up.

Adjust sharpness of display symbols with the dioptre focus knob (4). After

this adjustment no further dioptre adjustment should be required,

regardless of distance or other factors.

To adjust the display brightness, rotate the knob (17). Brightness level

from 0 to 20 is shown next to the icon in the upper part of the display

and then on the data panel.

Press button (15) to switch to display contrast setup mode. Contrast level

from 0 to 20 is shown next to the icon in the upper part of the display and

then on the data panel.

Subsequent press of the button “INV” (20) changes colour mode of the as

follows:

1st press – main part of the reticle is black, additional part is red;

2nd press – main part of the reticle is black, additional part is green;

3rd press – main part of the reticle is white, additional part is green;

4th press – main part of the reticle is white, additional part is red.

Choose a still object that is, for instance, 100 metres away.

Rotate the lens focus knob (16) to achieve best possible image

sharpness. To quickly adjust for a target 100m away, set the lens focus

knob (16) opposite mark “100” on the lens focus knob.

Starting the scope and image setup

Note: changing the mount position may require a slight re-zeroing.

The riflescope features two zeroing methods - traditional zeroing and “one

shot” zeroing.

Zeroing should be done at operating temperatures, by following the order of

these steps:

Mount the rifle with the riflescope installed on a bench rest.

Set a target at a distance of about 100m.

Adjust the riflescope according to the instructions of Section 9

“OPERATION”.

Aim the firearm at the target using the mechanical sight.

Using live ammunition, take 3-4 shots, continually aiming at the same hit

point on the target.

Examine the target and determine if the aiming point coincides with point of

impact, if you determine it's necessary to make corrections, you will need to

adjust your aiming point.

Traditional zeroing:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pulsar DIGISIGHT N770A Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info