633111
51
Zoom out
Zoom in
Vorherige Seite
1/176
Nächste Seite
51
4
51
D OPERATION WITH REMOTE CONTROL
G
NOTE!
Always aim the remote controller towards the receiver on the indoor unit and make sure there
are no obstacles in between the remote control and the receiver on the indoor unit. Otherwise
the remote control signal will not be picked up by the receiver and the air conditioner will not
work properly.
The maximum distance at which the remote control will work is approximately 6 to 7 meters.
G
NOTE!
Keep the remote controller where its signal can reach the receiver of the unit. When you select
the timer operation, the remote controller automatically transmits a signal to the indoor unit
at the specified time. If you keep the remote controller in a position that hinders proper signal
transmissions, a time lag of up to 15 minutes may occur.
Introduction of Function Buttons on the Remote Controller
1
2
8
6
7
4
15
3
12
11
5
9
10
14
13
a On/off Button: Push this button to start the unit operation. Push the button again to stop the unit
operation.
b Mode Button: Each time you press the button, a mode is selected in a sequence that goes from AUTO
COOL DRY HEAT and FAN only as the following figure indicates:
AUTO COOL DRY HEAT FAN
c + Button: Push the button to increase the indoor temperature setting to 30ºC.
d - Button: Push the button to decrease the indoor temperature setting to 17ºC.
e Fan Button: This button is used for selecting Fan Speed. Each time you press the button, a fan speed is
selected in a sequence that goes from AUTO, LOW, MED to HIGH, then back to Auto. When you select the
AUTO or DRY mode, the fan speed will be automatically controlled and you can not set the fan speed.
f SLEEP Button: Press this button to go into the Energy-Saving operation mode. Press it again to cancel.
This function can only be used on COOL, HEAT and AUTO mode and maintain the most comfortable
temperature for you. The unit automatically increases the set temperature by 1ºC per hour (in cooling
mode) or decreases the set temperature by 1ºC per hour (heating mode) during the first 2 hours. The air
conditioner will maintain this temperature (set temperature – or + 2 degrees) during the next 5 hours.
After this period, the air conditioner will shut itself down.
g Swing Button: Press the SWING button to activate the swing feature. Push the button again to stop.
fig. 1
51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Qlima - Zibro S3364 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info