Bedienungsanleitung Qlima - Zibro S3364 (Seite 53 von 176) (Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch)

633111

Zoom out

Zoom in

Vorherige Seite

1/176

Nächste Seite

a Transmission indicator: This transmission indicator lights when remote controller transmits signals to

the indoor unit.

b Mode display: Displays the current opeartion mode. Including Auto , Cool , Dry , Heat (Not

applicable to cooling only models), Fan .

c Temp. / Timer display: Displays the temperature setting (17º C ~ 30ºC). When you set the operating

mode to FAN, no temperature setting is displayed. And if in the TIMER mode, shows the ON and OFF

settings of the TIMER.

d Fan speed display: Displays the selected fan speed, AUTO (no display), LOW , MED and HIGH . The

fan speed is AUTO when the operating mode is either AUTO or DRY.

e ON / OFF display: Displayed by pressing the ON / OFF button. Press the ON / OFF button again to remove.

f Lock display: Displayed when LOCK mode is activated.

g Sleep display: Displayed under sleeping operation. Press the SLEEP button again to remove.

NOTE!

All items are shown in the Fig. 2 for the purpose of clear presentation. But during the actual

operation only the relative functional items are shown on the display panel.

Operating the Remote Controller

Install / Replace Batteries

Use two dry alkaline batteries (AAA/LR03).

Do not use rechargeable batteries.

1. Remove the battery cover on the back of the Remote Control by pulling it according to the arrow

direction shown on the cover.

2. Insert new batteries making sure that the (+) and (-) of battery are installed correctly.

3. Reattach the cover by sliding it back into position.

NOTE!

• When the batteries are removed, the remote controller erases all programming. After inserting

new batteries, the remote controller must be reprogrammed.

• When replacing batteries, do not use old batteries or a different type battery. This may cause

the remote controller to malfunction.

• If you do not use the remote controller for several weeks remove the batteries. Otherwise

battery leakage may damage the remote controller.

• The average battery life under normal use is about 6 months.

• Replace the batteries when there is no answering beep from the indoor unit or if the

Transmission Indicator light fails to appear.

• Never mix new and old batteries. Never use different battery types (e.g. alkaline and

manganese dioxide) simultaneously.

AUTOMATIC Operation

When the air conditioner is ready for use (check if unit is plugged in and whether electrical power is availa-

ble), switch on the power and the OPERATION indicator lamp on the display panel of the indoor unit starts

flashing.

1. Use the Mode select button to select AUTO.

2. Push the + or - button to set the desired room temperature.

3. Push the On/off button to start the air conditioner. The OPERATION lamp on the display panel of the

indoor unit lights. The FAN SPEED is automatically controlled.

4. Push the On/off button again to stop the unit operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Qlima - Zibro S3364 Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info