Bedienungsanleitung Quadra-Fire Classic Bay 1200 - Pellet

815525

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

15 04/217027-805J

S. Thermostat Other Features

TEMPERATURE CALIBRATION:

The internal temperature sensor in this thermostat is

accurately calibrated at the factory, and in most cases

alterations to this setting should not be needed. The

temperature calibration feature allows you to manually o󰀨set

the measured temperature by as much as plus or minus 5°F

(3°C) from its original value. If several thermostats are used

in the same house, this feature can be used to synchronize

this thermostat to the others.

Change the temperature calibration:

1. Move TEMPERATURE switch to OFF.

2. Move SET switch to RUN.

3. Press and hold both UP and DOWN buttons together for

at least 5 seconds; the words SET and CAL will appear

on the display along with a single ashing temperature

digit.

4. Use the UP or DOWN buttons to change the number of

degrees desired for adjustment; 0° is the default value

and also means no correction will be applied.

5. Press the NEXT button to accept the setting.

NOTE: All other features need to be completed in a timely

manner as the thermostat will time out after 10 seconds.

RST

Figure 15.1

COPY PROGRAM FEATURE:

Using similar instructions as SET TEMPERATURE

PROGRAMS the COPY button will allow a whole day of

set program events to be copied to another day.

1. Move Temperature switch to HEAT as well as move

SET switch to TEMP PROG position.

2. Starting with Monday, use the UP or DOWN buttons to

adjust the start time and set temperature for the MORN,

DAY, EVE, and NITE events. Press the COPY button

and then press the NEXT button to advance to Tuesday.

3. With Tuesday displayed press COPY button. As

all programs events from Monday will be copied to

Tuesday (this will advance automatically to the next

day; Wednesday, as the word COPY will appear on the

screen for one second).

4. Continue in this pressing COPY button to set desired

days with original setting.

NOTE: The word COPY will not appear on the display

for Monday, but will display each day afterwards for

approximately one second and the day of the week will

automatically advance forward to the next day.

KEYPAD LOCKOUT:

There is the option to lock the front panel buttons to prevent

unauthorized tampering of your thermostat settings.

To Lock the Keypad:

1. Move TEMPERATURE switch to HEAT.

2. Move SET switch to RUN.

3. Perform a single press of each button in the

following sequence:

- NEXT, NEXT, NEXT, HOLD

A padlock will appear on the display screen.

To Unlock the Keypad:

1. Move TEMPERATURE switch to HEAT.

2. Move SET switch to RUN.

3. Perform a single press of each button in the

following sequence:

- NEXT, NEXT, NEXT, HOLD

A padlock will no longer be present on the display screen.

HARDWARE RESET:

The hardware reset button; labeled HW RST, is a small

round push button that is located in the middle of the circuit

board, just below the battery holder (Figure 15.1). Pressing

this button will:

• Cause the LCD display screen to become fully populated

• Thermostat to perform an internal system check of

its components

If the thermostat appears to be acting in an erratic manner,

pressing the HW RST button may remedy this behavior.

The temperature programs are not erased when a hardware

reset is performed, however the clock will have to be

changed to match the current day and time.

SOFTWARE RESET:

Software reset is used to erase ALL temperature events,

and to return all user-adjustable software settings back to

their original factory default settings.

To Perform a Software Rest:

1. Verify the thermostat’s keypad is not locked.

2. Move TEMPERATURE switch to OFF.

3. Press and hold the UP, DOWN, and NEXT buttons all

at the same time for at least 5 seconds. When the LCD

display screen will become fully populated let go of all

buttons at that point the screen will return to normal.

The clock will have to be changed to match the current day

and time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quadra-Fire Classic Bay 1200 - Pellet - Insert Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Quadra-Fire Classic Bay 1200 - Pellet - Insert

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info