Bedienungsanleitung Quickie HeliX 2 (Seite 15 von 188) (Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

713890

Zoom out

Zoom in

Vorherige Seite

1/188

Nächste Seite

15HeliX

ENGLISH

ADJUSTING THE CALF PAD

(Fig 19).

The calf pad can be adjusted as

follows:

Height: Open bolt (4) and move the

clamping piece to the desired

position. By rotating the clamping

piece also the angle can be

adjusted.

Depth: Open bolt (5) and move the

calf pad into the desired position.

Width: Open bolt (5) and position the

spacers (6) behind the pad, to get

the desired position.

WARNING!

• Keep hands clear of the adjustable mechanism between the

frame and the movable parts of the foot rest, while elevating or

lowering the footrest.

• Always make sure that the fasteners are secure.

• The foot rests must not be used to lift or to carry the

wheelchair.

• Risk of trapping fingers! When moving the foot rest up or

down, do not put your fingers in the adjusting mechanism

between the moving parts of the foot rest.

AMPUTEE SUPPORT

(Fig.20).

The Amputee Support can be

adjusted in every direction as

required.

CASTORS, CASTOR PLATES, FORKS

The wheelchair may veer slightly to the right or left, or the castors

may wobble. This may be caused by the following:

• Forward and/or reverse wheel motion has not been set properly.

• The castor angle has not been set correctly.

• Castor and/or rear wheel air pressure is incorrect; the wheels do

not turn smoothly.

The wheelchair will not move in a straight line if the castors have

not been properly adjusted. Castors should always be adjusted by

an authorised dealer. The wheel locks must be checked every time

the rear wheel position has been altered.

The seat height is determined by the

castor and rear wheel position. The

seat height can be adjusted by

altering the position of the rear

wheels and the castors and by using

spacers, (Fig.21).

CAUTION!

After adjusting the seat height, all

screws must be re-tightened and the

wheel lock must be readjusted.

FIG. 19

FIG. 20

Options - Castors

Options - Castor Adapter

NOTE:

You can change the angle of the castor axle by altering the position

of the castor/rear wheel. This should always be approx. 90°.

ADJUSTING THE CASTOR AXLE ANGLE:

Release the screws (1), pull the castor adaptor outwards, set a 90°

angle and then re-tighten the screws (Fig. 22-24).

CAUTION!

The castor axle angle must be set the same on both sides (check by

marking).

HORIZONTAL AXLE POSITION

The axle plate can be adjusted

forwards to give greater

manoeuvrability or to the rear to give

greater stability (Fig. 22).

The larger the wheelbase, the greater

the security against your wheelchair

tipping over.

0° / 3° CAMBER:

By rotating the axle adapter by 180° the camber can be set to 3° or

0°.

NOTE:

When making this adjustment, the wheelbase must also be

re-adjusted afterwards.

CAUTION!

Wheel locks must be adjusted to suit the new position!

Fig. 21

Fig. 24

Fig. 22

Fig. 23

90°

Height-adjustable backrest

The backrest height can be

adjusted from 35 - 50 cm

(depending on the backrest

position). Release the bolts

(1)+(2), and push the backrest

tube to the desired position.

Tighten up the bolts again

(Fig. 25).

Options - Backrest

Fig. 25

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quickie HeliX 2 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info