Bedienungsanleitung Quickie Life i (Seite 20 von 96) (Englisch, Holländisch, Französisch, Italienisch)

713889

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

Life i Rev.6.0

Castor

Castor, Castor adapter, Castor fork (Fig. 6.20 - 6.20.2)

From time to time the wheelchair may veer slightly to the right or

left or the castors may flutter.

This may be caused by the fol low ing:

Forward and/or reverse wheel motion has not been set properly.

The castor angle has not been adjusted properly.

Castor and/or rear wheel air pressure is incorrect; wheels do not

turn smoothly.

The optimum adjustment of the castors is required so that the

wheelchair runs in a straight line. Casters should always be

adjusted by an authorized dealer.

The castor plates must be re-adjusted, and the wheel locks must

be checked every time the rear wheel position has been altered.

Check the setting of the castor adapter (1) by placing a set-

square next to it and looking at it from the front. Make sure that

the adapter is at right angles to the floor. By undoing the screws

(2) and moving the adapter, you can then re-adjust the wheels to

their optimum position, by adjusting the corresponding teeth

segments. Make sure that after any adjustment work, all screws

are tightened correctly (see the page on torque).

The screws used are fitted with threadlock at the factory and can

be adjusted 5 x after fitting. After that they should be replaced or

alternatively re-secured with threadlock to medium tightness.

Fig. 6.20

90°

Axle plate

Axle plate (Fig. 6.21)

The position of the centre of gravity in relation to the rear wheel

is an important factor for easy and comfortable driving. Several

positions are possible. If you move the perforated plate to the

rear, the chair is in a safe position, but at the same time is not so

manoeuvrable, as it is when the perforated plate is positioned

further forward.

By moving the axle plate up and down, you can adjust the seat

height of the wheelchair. Make sure that after any adjustment

work, all screws are tightened correctly (see the page on

torque).

CAUTION!

If necessary, the brakes and castors must be re-adjusted.

Fig. 6.21

Cambers

Cambers (Fig. 6.22)

The camber of the chair can be adjusted from 0° to 3°.

Doing this gives increased stability against the wheelchair falling

to the side, and will also improve the wheelchair’s

manoeuvrability.

Loosen the screws on the axle plate and then turn the adapter

by 180̊. Then tighten the screws again (see the page on torque).

Setting the wheel camber increases the overall width of the

wheelchair (each degree adds on approx. 100 mm).

CAUTION!

If necessary, the brakes and castors must be re-adjusted.

Fig. 6.22

Front seat height

To adjust the front seat height, please loosen the screws A (2

on each side) and set to the required seat height. Ensure that

both sides are at the same height and then re-tighten the

screws. Please note the torque required (see the page on

torque).

Fig. 6.20.2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quickie Life i Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info