Bedienungsanleitung Quickie Life i (Seite 21 von 96) (Englisch, Holländisch, Französisch, Italienisch)

713889

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

Life i Rev.6.0

Folding stabilising bar

This bar is used to stabilize the

backrest.

To be able to fold the wheelchair,

the release lever must be pushed

inwards (Fig. 6.29) or released and

the stabilising must be flipped

downwards. When unfolding the

wheelchair, please make sure that

the stabilising bar is locked into

position.

Headrest (Fig. 6.28)

You can adjust the height of the

headrest and it can be moved

forwards and backwards,

horizontally. To do this, loosen the

screw (1 or 2). This is how you can

adjust to the required positions.

Re-tighten the screws (see the

page on torque).

Adjustable Back Sling,

(Fig. 6.26)

The adjustable back sling can be

adjusted for tension by parting the

Velcro® straps and moving them

through the buckles (1). When the

desired tension is achieved, press

the Velcro back together.

Repeat the process for each strap.

The back sling upholstery can be

accessed from the inside via an

opening and can be padded to suit

individual tastes.

WARNING!

Ensure that each strap is firmly secured before using the wheelchair.

Backrest

Height-adjustable Backrest

The backrest height can be

adjusted from 350 mm -

500 mm (depending on the

backrest position). Release the

bolts (1)+(2), and push the

backrest tube to the desired

position. Tighten up the bolts

again (Fig. 6.23).

Fig. 6.23

Angle Adjustable Backrest

The angle of the backrest

can be set to 6 different

positions (-5° forwards, 0°, 5°,

10°, 15° and 20° backwards).

To adjust the angle, remove

the screw (1), set the desired

angle and then re-tighten the

screw. (Fig. 6.24). By

releasing the clamp lever (1)

the backrest height can be

infinitely adjusted from 350

mm – 500 mm.

Fig. 6.24

Adjusting the backrest

angle

(7° - 30°)

By pulling both levers

together (1), you can release

the backrest and then move

it to the desired position.

On releasing the two levers

(1) the backrest will

automatically lock into place

(Fig. 6.25).

WARNING!

• The reclining backrest can only be used in conjunction with

the wheelbase extension.

• It is recommended that the reclining backrest is used in

conjunction with anti-tip tubes (maximum ground clearance

30 mm - 50 mm).

• We recommend that the reclining backrest is used in

conjunction with a stabilising bar.

Fig. 6.25

Trunk support

The trunk support can be adjusted

in angle, depth and height (see Fig.

6.27). It can be swung away by

turning the release lever (1).

Headrest

Fig. 6.28

Stabilizing Bar

Fig. 6.29

Fig. 6.27

One Hand Operation

(Fig. 6.30 - 6.30.1)

To propel the chair straight forward

both handrims must be used.

To fold the wheelchair disconnect

the telescopic bar by pushing the

release inward (1). To take off the

wheels pull release knob (2).

CAUTION!

Make always sure that the

connections are set properly to

avoid injuries.

Fig. 6.26

Fig. 6.30

Fig. 6.30.1

Options – One Hand Operation

(1)

(2)

(1)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Quickie Life i Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info