Bedienungsanleitung RadioShack PRO-2018 - 200 Channel (Seite 18 von 36) (Englisch)

570007

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Searching the One Touch Banks

2. Press

ENT

again to store the frequency. The channel

and frequency flash twice. If you want to cancel the

operation, press

TUNE/CLEAR

instead of

ENT

. After

storing the frequency, the scanner continues to search

for frequencies.

5ECPPKPI"VJG"5VQTGF"%JCPPGNU

To set the scanner to continuously scan through all

channels with stored frequencies, repeatedly press

SCAN

until

I97D

I97DI97D

I97D

and

appear. The scanner rapidly scans until it

finds an active frequency.

If the scanner finds an active frequency, it stops and

displays that channel and frequency number, then it

automatically begins scanning again when the conversation

on that frequency ends unless delay is set for the channel

(see “Delay” on Page 20).

6WTPKPI"%JCPPGN/5VQTCIG"$CPMU"1HH"CPF"1P

Channel-storage banks (1-10) are on when they have a bar

underneath them and off when no bar appears underneath

them. To turn off a channel-storage bank, press the bank's

number key during scanning. The bar under the bank's

number disappears.

To turn on a channel-storage bank (1-10) during scanning,

press the bank's number key. A bar appears under the

bank's number.

If no transmission is found, the scanner continues to scan

through all selected banks.

/QPKVQTKPI"C"5VQTGF"%JCPPGN

You can continuously monitor a specific channel without

scanning. This is useful if you hear an emergency

transmission on a channel and do not want to miss any

details – even though there might be periods of silence – or

if you simply want to monitor that channel.

Follow these steps to manually select a channel.

1. Repeatedly press

SCAN/MAN

until

C7D

C7DC7D

C7D

appears.

2. Enter the channel number (1-200).

3. Press

SCAN/MAN

again.

"016'"

Scanning the Stored

Channels

• To reverse the scanning

direction, press

• To set the scanner to remain on

the current channel for 2

seconds after the transmission

ends, see “Delay” on Page 20.

• To set the scanner to remain on

the current channel, even after

the transmission stops, press

SCAN/MAN at any time during

the transmission.

C7D

C7DC7D

C7D appears

and

I97Dý

I97DýI97Dý

I97Dýdisappears (see

“Monitoring a Stored Channel”

on Page 18).

• To lock out channels so the

scanner does not stop for a

transmission on those channels,

see “Locking Out Channels or

Frequencies” on Page 21.

Turning Channel-Storage

Banks Off and On

• The scanner does not scan any

of the channels within the banks

you have turned off.

• You cannot turn off all banks.

There must be at least one

active bank.

• You can manually select any

channel in a bank, even if the

bank is turned off.

• When you turn on a bank during

scanning, the scanner moves to

the selected bank and scans it.

20-424.fm Page 18 Monday, September 9, 2002 9:44 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

RadioShack PRO-2018 - 200 Channel Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info