Bedienungsanleitung RadioShack PRO-2053 - 300 Channel (Seite 29 von 56) (Englisch)

570004

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Special Features

To change the receive mode, repeatedly

press

MODE

. The receive mode changes as

follows:

ã)

ã)ã)

ã)

— accesses the AM mode

")")

— accesses the FM mode

)+)+

— accesses the FM Mode, Motorola

Trunking System (with a 4- or 5-digit ID

code)

! !

— accesses the FM Mode, EDACS

Trunking System (with 4-digit decimal ID

code or 5-digit AFS code)

Note:

MO (MOT) and ED modes are not

available when the scanner tunes up or

down through the frequency ranges in which

the trunking operation is not used.

USING THE ATTENUATOR

To reduce interference or noise caused by

strong signals, you can reduce the scanner's

sensitivity to these signals.

There are two attenuator modes in your

scanner. In normal attenuator mode, you set

the attenuator in each channel or each band/

group in the search and tune mode. In global

mode, you set the attenuator only once. The

global setting affects every mode.

Press

ATT

to turn on or off the attenuator

while the channel number is indicated, or

while the scanner is searching through

bands/groups. When the attenuator is on,

ãã

appears at the seventh digit in the top line.

When you turn it off,

ãã

changes to "

ôô

". You

cannot set the attenuator while the scanner

is scanning.

Press

FUNC

then

ATT

to set the attenuator to

the global mode.

#CF98Cý ã00ô

#CF98Cý ã00ô#CF98Cý ã00ô

#CF98Cý ã00ô

appears for 2

seconds at the bottom line and

Wý

WýWý

Wý

(on) or

(off) appears. Press

ATT

to turn on or off the

attenuator.

ã00FE

ã00FEã00FE

ã00FE

ã00V

ã00Vã00V

ã00Vý

appears on the

bottom line while scanning.

Press

FUNC

then

ATT

again to turn off the

global attenuation mode.

*FID8Cýã00

*FID8Cýã00*FID8Cýã00

*FID8Cýã00

is indi-

cated at the bottom line for 2 seconds.

Note:

If you turn on the attenuator, the scan-

ner might not receive weak signals.

TURNING THE KEY TONE ON

AND OFF

Each time you press any of the scanner's

keys, the scanner sounds a tone. To turn the

scanner's key tone off or on:

1. If the scanner is on, turn

VOLUME OFF/

MAX

counterclockwise until it clicks to

turn the scanner off.

2. Turn

VOLUME OFF/MAX

clockwise to

turn the scanner on.

3<C:FD<ý 0Fý L8C

3<C:FD<ý 0Fý L8C3<C:FD<ý 0Fý L8C

3<C:FD<ý 0Fý L8C

0ILEB@E>

0ILEB@E>0ILEB@E>

0ILEB@E>

appears.

3. While

3<C:FD<ý 0Fý L8Cý 0ILEB@E>

3<C:FD<ý 0Fý L8Cý 0ILEB@E>3<C:FD<ý 0Fý L8Cý 0ILEB@E>

3<C:FD<ý 0Fý L8Cý 0ILEB@E>

appears, press

to turn on the key tone

to turn it off.

CHANGING THE DISPLAY

CONTRAST

1. Press

MAN

2. Press

FUNC

then

1J<ý 1Gó FNEý B<PJ

1J<ý 1Gó FNEý B<PJ1J<ý 1Gó FNEý B<PJ

1J<ý 1Gó FNEý B<PJ

KFýJ<Ký:FEKI8JKô

KFýJ<Ký:FEKI8JKôKFýJ<Ký:FEKI8JKô

KFýJ<Ký:FEKI8JKô

appears.

3. Press

to select the contrast.

4. Press

ENTER

to set the display contrast.

CLONING PROGRAMMED

DATA

You can transfer programmed data to and

from another RadioShack PRO-2053 or a

PRO-93 scanner using an optional connect-

ing cable with

-inch phone plugs on both

ends, (not included) available at your local

RadioShack store.

Follow these steps to clone the data.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

RadioShack PRO-2053 - 300 Channel Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info