Bedienungsanleitung Raymarine Dragonfly (Seite 32 von 118) (Englisch)

558415

Zoom out

Zoom in

Vorherige Seite

1/118

Nächste Seite

4.8 Testing the transducer

Once the initial mounting procedures have been

carried out, the transducer must be tested prior to

nishing the mounting.

The testing should be carried out with your vessel in

the water, with a depth greater than 0.7 m (2.3 ft) but

less than the maximum depth limit of the system.

The Sonar application will be able to maintain

readings at depths greater than the DownVision

application.

Note: It may not always be possible to obtain

depth readings at higher speeds due to air bubbles

passing under the transducer.

1. Press and hold the Power button until a beep is

heard.

2. Complete the Start-up wizard settings.

3. Use the View switcher to open a view which

contains the Sonar or DownVision application.

If the unit is operating correctly the bottom should

be visible on-screen and the depth reading

displayed.

4. Start moving your vessel at a low speed and

ensure the depth reading and bottom are shown

and that you have a clear image on-screen.

5. Gradually increase the vessel speed up to your

usual cruising speed, whilst checking the display

if the image becomes poor, starts skipping or

missing the bottom then the transducer needs

to be adjusted.

6. Height and angle adjustments should be made in

small increments, and re-tested each time until

you obtain optimum performance.

7. To adjust the angle of the transducer loosen the

pivot bolt approximately 3 turns and then pivot

the transducer either up or down.

8. Re-tighten the pivot bolt before re-testing.

9. When you achieve optimum performance at

the desired vessel speeds you can nish the

transducer mounting.

Note: It may be necessary to make several

adjustments to the transducer before obtaining

optimum performance.

4.9 Finishing the transducer mounting

Once you have achieved optimum performance at

the desired vessel speeds the transducer must be

locked into position to nish the installation.

Note: If the transducer requires repositioning

ensure all old holes are lled with marine grade

sealant.

1. Loosen the kick-up adjustment screw.

2. Lift up the transducer and bracket pivot arm to

gain access to the mounting holes.

3. Drill the locking hole location taking care not to

damage the mounting bracket.

4. Fill the locking hole with marine grade sealant.

5. Secure the transducer and bracket by fully

tightening all 3 mounting screws.

6. Push the transducer and pivot arm down until it

clicks into position.

7. Re-tighten the kick-up adjustment screw to the

desired level.

Note: The Kick-up adjustment screw needs to be

tight enough to prevent kick-up during high speeds

but loose enough to enable the kick-up feature

to activate if an object hits the transducer when

underway.

Dragony® 6/ Dragony® 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Raymarine Dragonfly Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Raymarine Dragonfly

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info