Bedienungsanleitung Raymarine Dragonfly (Seite 34 von 118) (Englisch)

558415

Zoom out

Zoom in

Vorherige Seite

1/118

Nächste Seite

5.1 General cabling guidance

Cable types and length

It is important to use cables of the appropriate type

and length

• Unless otherwise stated use only standard cables

of the correct type, supplied by Raymarine.

• Ensure that any non-Raymarine cables are of the

correct quality and gauge. For example, longer

power cable runs may require larger wire gauges

to minimize voltage drop along the run.

Routing cables

Cables must be routed correctly, to maximize

performance and prolong cable life.

• Do NOT bend cables excessively. Wherever

possible, ensure a minimum bend diameter of 200

mm (8 in) / minimum bend radius of 100 mm (4 in).

100 mm (4 in)

200 mm (8 in)

• Protect all cables from physical damage and

exposure to heat. Use trunking or conduit where

possible. Do NOT run cables through bilges or

doorways, or close to moving or hot objects.

• Secure cables in place using tie-wraps or lacing

twine. Coil any extra cable and tie it out of the way.

• Where a cable passes through an exposed

bulkhead or deckhead, use a suitable watertight

feed-through.

• Do NOT run cables near to engines or uorescent

lights.

Always route data cables as far away as possible

from:

• other equipment and cables,

• high current carrying ac and dc power lines,

• antennae.

Strain relief

Ensure adequate strain relief is provided. Protect

connectors from strain and ensure they will not pull

out under extreme sea conditions.

Cable shielding

Ensure that the cable is properly shielded that the

cable shielding is intact (e.g. hasn’t been scraped off

by being squeezed through a tight area).

5.2 Cable connection

The display has a combined power and transducer

cable that is attached to the transducer.

(0.6)VM

D12 642 -1

1. Display rear panel connection.

2. Transducer with cable attached.

3. Drain wire (The drain wire is the wire with a

sheath).

4. Black wire (12 V dc negative).

5. Red wire (12 V dc positive).

Power distribution

Raymarine recommends that all power connections

are made via a distribution panel.

• All equipment must be powered from a breaker or

switch, with appropriate circuit protection.

• All equipment should be wired to individual

breakers if possible.

Warning: Power supply voltage

Connecting this product to a voltage

supply greater than the specied

maximum rating may cause permanent

damage to the unit. Refer to the Technical

specication section for voltage rating.

Warning: Product grounding

Before applying power to this product,

ensure it has been correctly grounded, in

accordance with the instructions in this

guide.

Grounding — Dedicated drain wire

The power cable supplied with this product includes

a dedicated shield (drain) wire for connection to a

vessel's RF ground point.

It is important that an effective RF ground is

connected to the system. A single ground point

should be used for all equipment. The unit can be

grounded by connecting the shield (drain) wire of

the power cable to the vessel's RF ground point.

Dragony® 6/ Dragony® 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Raymarine Dragonfly Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Raymarine Dragonfly

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info