Bedienungsanleitung Reebok Edge Bike (Seite 5 von 5) (Englisch)

559665

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

Power on state: The gear motor will return to zero automatically, when the

signal of motor cannot be detected for more than 4

seconds then the gear motor’s driver will be cut off

immediately and show the E1 on the LCD display. All the

other digital and function mark are blank, and the output

signals are cut off also.

E2 (ERROR 2): When the monitor read the memory data, if the I.D. code is not correct or

the memory IC damages then the monitor will show E2 immediately at

power on.

E3 (ERROR 3): After 4 seconds by start mode, the computer detects the faulty motor did

not leave the zero point then the LCD bar displays “E3”.

LCD Workout Graphics

PRESET PROGRAM PROFILES:

PROGRAM 1 PROGRAM 2 PROGRAM 3

MANUAL ROLLING VALLEY

PROGRAM 4 PROGRAM 5 PROGRAM 6

FAT BURN RAMP . MOUNTAIN

P6.

2. Press ENTER key to enter your workout program.

3. The TIME will flash and you can press UP or DOWN key to set

your exercise TIME. Press ENTER key to confirm your desired

workout TIME.

4. The DISTANCE will flash and you can press UP or DOWN keys to

set your target DISTANCE. Press ENTER key to confirm your

desired workout DISTANCE.

5. The CAL will flash and you can press UP or DOWN keys to set

your exercise CALORIES. Press ENTER key to confirm your

desired workout CALORIES.

6. Press START/STOP key to begin exercise.

Operation Instruction:

1. Plug in the power

Plug in the adaptor to the equipment then the computer will produce a beep sound

and then turn on the computer at the Manual mode.

2. Program select and setting value

Ａ. Use the PROGRAM key to select program mode and then press ENTER to

confirm your exercise mode.

Ｂ. At the Manual mode, the computer would allow user to use the UP or DOWN key

to set up specific workout TIME, DISTANCE and CALORIES. Press UP + DOWN

keys can clear out the setting value to zero.

C. Press the START/STOP key to begin exercise.

D. When you reach the target, the computer will produce beep sounds and then stop.

E. If you set up more than one target and you would like to reach next target, press

START/STOP key to keep on exercise.

Operation guide:

The computer will enter CLOCK setting mode when power on it. You should set up the

current time by the UP or DOWN keys to adjust the Hours and minutes.

Clock Mode:

a. The computer will enter the clock mode when there is no signal input or no keys be

pressed after 4 minutes. You can press ENTER key to switch the clock and

temperature at the clock mode or press other keys to quit the clock mode.

b. You can set up the CLOCK by holding ENTER key for over 2 seconds then adjust by

UP or DOWN keys.

c. By holding the ENTER and UP keys together for over two seconds, you can check the

current clock at “NO SPEED” mode.

Error Message:

E1 (ERROR 1): Normal state: During workout if the computer does not receive a signal

from the motor for more than 4 seconds error 1 will be displayed,the

machine will automatically check 3 times in order to ensure this is the case.

b. During the stop mode, press the key to START exercise.

c. Press this key can allow you to quickly start the computer

without selecting a program. For Manual workout only. Time

automatically begins to count up from zero

1. UP key: a. Press the key to increase the resistance during exercise mode.

b. During the setting mode, press the key to increase the value of Time,

Distance and Calories.

2. DOWN key: a. Press the key to decrease the resistance during exercise mode.

b. During the setting mode, press the key to decrease the value of Time,

Distance, and Calories.

3. ENTER key: a. During the setting mode, press the key to accept the current data

entry.

b. At the stop mode, by holding this key for over two seconds the

computer will re-power on and all the value will reset to zero.

c. During the START stage, press the key to exit the auto-scan

mode to manual-scan mode. .

4. PULSE RECOVERY key: Press the key to activate heart rate recovery function.

5. PROGRAM key: Press the key to select the program from P1 to P6.

Program Introduction & Operation:

Manual Program: Manual

P1 is a manual program. User can start exercise by pressing START/STOP key. The

default resistance level is 3. Users may exercise in any desirous of resistance level

(Adjusting by UP/DOWN keys during the workout) with a period of time or a number

of calories or a certain distance.

Operations: 1. Press the ENTER key to enter MANUAL (P1) program.

2. The TIME will flash and you can press UP or DOWN key to set

your exercise TIME. Press ENTER key to confirm your desired

workout TIME.

3 The DISTANCE will flash and you can press UP or DOWN keys to

set your target DISTANCE. Press ENTER key to confirm your

desired workout DISTANCE.

4 The CAL will flash and you can press UP or DOWN keys to set

your exercise CALORIES. Press ENTER key to confirm your

desired workout CALORIES.

5 Press START/STOP key to begin exercise.

Preset Program: Rolling, Valley, Fat Burn, Ramp, and Mountain Program

PROGRAM 2 to PROGRAM 6 is the preset programs. Users can exercise with

different level of resistance in different intervals as the profiles show. Users may exercise

at any level of resistance level (Adjusting by UP/DOWN key during the workout)

with a period of time or a number of calories or a certain distance.

Operations: 1. Use PROGRAM key to select one of the above programs from P2 to

18 19

Reebok Edge Bike Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info