Bedienungsanleitung Remeha Flexistor (Seite 17 von 36) (Englisch)

805760

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

The following extract is taken from latest G3 Regulations

Discharge pipes from safety devices

Discharge pipe D1

3.50 Safety devices such as temperature relief valves or combined temperature and pres-

sure relief valves (see paragraphs 3.13 or 3.18) should discharge either directly or by way of a

manifold via a short length of metal pipe (D1) to a tundish.

3.51 The diameter of discharge pipe (D1) should be not less than the nominal outlet size of the

safety device, e.g. temperature relief valve.

3.52 Where a manifold is used it should be sized to accept and discharge the total discharge from

the discharge pipes connected to it.

3.53 Where valves other than a temperature and pressure relief valve from a single unvented

hot water system discharge by way of the same manifold that is used by the safety devices, the

manifold should be factory tted as part of the hot water storage system unit or package.

Tundish

3.54 The tundish should be vertical, located in the same space as the unvented hot water stor-

age system and be tted as close as possible to, and lower than, the safety device, with no more

than 600mm of pipe between the valve outlet and the tundish (see Diagram 1).

Note: To comply with the Water Supply (Water Fittings) Regulations, the tundish should incorpo-

rate a suitable air gap.

3.55 Any discharge should be visible at the tundish. In addition, where discharges from safety

devices may not be apparent, e.g. in dwellings occupied by people with impaired vision or mo-

bility, consideration should be given to the installation of a suitable safety device to warn when

discharge takes place, e.g. electronically operated.

Discharge pipe D2

3.56 The discharge pipe (D2) from the tundish should:

a. have a vertical section of pipe at least 300mm long below the tundish before any elbows or

bends in the pipework (see Diagram 1); and

b. be installed with a continuous fall of at least 1 in 200 thereafter.

3.57 The discharge pipe (D2) should be made of:

a. metal; or

b. other material that has been demonstrated to be capable of safely withstanding temperatures

of the water discharged and is clearly and permanently marked to identify the product and per-

formance standard (e.g. as specied in the relevant part of BS 7291- 1:2006 Thermostatic pipes

and ttings for hot and cold water for domestic purposes and heating installations in buildings.

General requirements).

3.58 The discharge pipe D2 should be at least one pipe size larger than the nominal outlet size

of the safety device unless its total equivalent hydraulic resistance exceeds that of a straight pipe

9m long, i.e. for discharge pipes between 9m and 18m the equivalent resistance length should

be at least two sizes larger than the nominal outlet size of the safety device; between 18 and

27m at least 3 sizes larger, and so on; bends must be taken into account in calculating the ow

resistance. See Diagram 1, Table 3.1 and the worked example.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Remeha Flexistor Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info