805735
78
Zoom out
Zoom in
Vorherige Seite
1/92
Nächste Seite
Code Description Solution
E00.20 Flue gas temperature sensor is either removed or
measures a temperature below range
Open circuit in flue gas sensor:
Bad connection: check the wiring and connectors.
Incorrectly fitted sensor: check that the sensor has
been correctly fitted.
Faulty sensor: replace the sensor.
E00.21 Flue gas temperature sensor is either shorted or
measures a temperature above range
Flue gas sensor short-circuited:
Bad connection: check the wiring and connectors.
Incorrectly fitted sensor: check that the sensor has
been correctly fitted.
Faulty sensor: replace the sensor.
E00.40 Water pressure sensor is either removed or
measures a temperature below range
Hydraulic pressure sensor open:
Bad connection: check the wiring and connectors.
Incorrectly fitted sensor: check that the sensor has
been correctly fitted.
Faulty sensor: replace the sensor.
E00.41 Water pressure sensor is either shorted or measures
a temperature above range
Hydraulic pressure sensor short-circuited:
Bad connection: check the wiring and connectors.
Incorrectly fitted sensor: check that the sensor has
been correctly fitted.
Faulty sensor: replace the sensor.
E01.04 5x Error of unintended Flame Loss occurance Flame loss occurs 5 times:
Vent the gas supply to remove air
Check that the gas valve is fully opened
Check the gas supply pressure
Check the operation and setting of the gas valve
unit
Check that the air supply inlet and flue gas outlet
are not blocked
Check that there is no recirculation of flue gases
E01.12 Return tempearture has a higher temperature value
than the flow temperature
Flow and return reversed:
Bad connection: check the wiring and connectors
Water circulation in wrong direction: check the cir
culation (direction, pump, valves)
Incorrectly fitted sensor: check that the sensor has
been correctly fitted
Malfunctioning sensor: check the Ohmic value of
the sensor
Faulty sensor: replace the sensor
E02.04 Parameter Error Configuration error:
Reset CN1 and CN2
See
The data plate for the CN1 and CN2 val
ues.
E02.13 Blocking Input of the Control Unit from device
external environment
Blocking input is active:
External cause: remove external cause
Wrong parameter set: check the parameters
E02.15 External CSU Timeout CSU time out:
Bad connection: check the wiring and connectors
Faulty CSU: Replace CSU
E02.17 Gas Valve Control unit communication has exceeded
feedback time
Communication error with the security kernel:
Restart the boiler
Replace the CU-GH PCB
E02.35 Safety critical device has been disconnected Communication fault
Carry out an auto-detect
11 Troubleshooting
78 7665063 - v.05 - 18102018
78

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Remeha Gas 220 Ace wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Remeha Gas 220 Ace

Remeha Gas 220 Ace Bedienungsanleitung und Installationsanweisung - Deutsch - 88 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info