805735
80
Zoom out
Zoom in
Vorherige Seite
1/92
Nächste Seite
Code Description Solution
E04.10 5 Unsuccessful burners starts detected Five failed burner starts:
No ignition spark:
Check the wiring between the CU-GH PCB and
the ignition transformer
Check the ionisation/ignition electrode
Check breakdown to earth
Check the condition of the burner cover
Check the earthing
SU PCB faulty: replace the SU PCB
Ignition spark but no flame:
Vent the gas pipes to remove air
Check that the air supply inlet and flue gas outlet
are not blocked
Check that the gas valve is fully opened
Check the gas supply pressure
Check the operation and setting of the gas valve
unit
Check the wiring on the gas valve unit
Replace the CU-GH PCB
Flame present, but ionisation has failed or is inade
quate:
Check that the gas valve is fully opened
Check the gas supply pressure
Check the ionisation/ignition electrode
Check the earthing
Check the wiring on the ionisation/ignition elec
trode.
E04.11 VPS Gas Valve proving failed Gas leakage control fault:
Bad connection: check the wiring and connectors
Gas leakage control VPS faulty: Replace the GPS
Gas valve unit faulty: Replace the gas valve unit
E04.12 False flame detected before burner start False flame signal:
The burner remains very hot: Set the O2
Ionisation current measured but no flame should
be present: check the ionisation/ignition electrode
Faulty gas valve: replace the gas valve
Faulty ignition transformer: replace the ignition
transformer
E04.13 Fan speed has exceeded normal operating range Fan fault:
Bad connection: check the wiring and connectors.
Fan operates when it should not be operating:
check for excessive chimney draught
Faulty fan: replace the fan
E04.15 The flue gas pipe is blocked Flue gas outlet is blocked:
Check that the flue gas outlet is not blocked
Restart the boiler
E04.17 The driver for the gas valve is broken Gas valve unit fault:
Bad connection: check the wiring and connectors
Faulty gas valve unit: Replace the gas valve unit
E04.23 Gas Valve Control internal locking Restart the boiler
Replace the CU-GH PCB
11.2 Error memory
The boiler control unit has an error memory. It stores the last 32 errors that
have occurred.
11 Troubleshooting
80 7665063 - v.05 - 18102018
80

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Remeha Gas 220 Ace wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Remeha Gas 220 Ace

Remeha Gas 220 Ace Bedienungsanleitung und Installationsanweisung - Deutsch - 88 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info