Bedienungsanleitung Remeha Sol Plus (Seite 60 von 72) (Englisch)

805721

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Installation Indications, functions and options MessagesCommissioningOperation and function

Collector minimum limitation

OCN / OCN1 / OCN2

Collector minimum limitation option

Adjustment range: OFF / ON

Factory setting: OFF

CMN / CMN1 / CMN2

Minimum collector temperature

Adjustment range:

10.0 … 90.0 °C [50.0 … 190.0 °F]

Factory setting: 10.0 °C [50.0 °F]

If the collector minimum limitation option is activated, the pump (R1 / R2) will only

be switched on, if the adjustable collector minimum temperature is exceeded. The

minimum temperature prevents the pump from being switched on too often at low

collector temperatures. A hysteresis of 5 K [10 °Ra] is set for this function. If the

collector minimum limitation is active, ❄ is displayed (ashing).

Note

If OSTC or OCF is active, the collector minimum limitation will be over-

ridden. In that case, the collector temperature may fall below CMN.

Antifreeze function

OCF / OCF1 / OCF2

Antifreeze function option

Adjustment range: OFF / ON

Factory setting: OFF

CFR / CFR1 / CFR2

Antifreeze temperature

Adjustment range:

-40.0 … +10.0 °C [-40.0 … +50.0 °F]

Factory setting: +4.0 °C [+40.0 °F]

The antifreeze function activates the loading circuit between the collector and the

store when the temperature falls below the adjusted antifreeze temperature. This

will protect the uid against freezing or coagulating. If the adjusted antifreeze tem-

perature is exceeded by 1 K [2 °Ra], the loading circuit will be deactivated.

If the antifreeze function is activated, ❄ is displayed. If the antifreeze function is

active, ⓵ and ❄ are displayed (ashing).

Note

Since this function uses the limited heat quantity of the store, the anti-

freeze function should only be used in regions with few days of tempera-

tures around the freezing point.

The antifreeze function will be suppressed if the store temperature falls

below +5 °C [+40 °F] in order to protect the store from frost damage.

Priority logic

Note

Priority logic can be used in 2-store system only (Arr = 4, 5, 6).

PRIO

Priority

Adjustment range: SE 1, SE 2, Su 1, Su 2, 0, 1, 2

Factory setting: Arr 4: 2, Arr 5, 6: 1

If a 2-store system has been selected, the priority logic determines how the heat is

divided between the stores. Different types of priority logic are adjustable:

• spreaded loading (SE 1 and SE 2)

• successive loading (Su 1 and Su 2)

• parallel loading (0)

• store sequence control (1 and 2)

If priority PRIO SE 1 or SE 2 (only available in Arr 6) is adjusted, the subordinate

store will be loaded in parallel to the priority store if the temperature difference

between the collector and the priority store (store 1 for SE 1, store 2 for SE 2)

exceeds the adjusted value DTSE and the subordinate store has not reached its

maximum temperature.

Parallel loading will stop as soon as the temperature difference between the collec-

tor and the priority store falls by 2 K [4 °Ra] below DTSE or the subordinate store

reaches its maximum temperature.

If priority PRIO Su 1 or Su 2 is adjusted, the stores are loaded successively. The

subordinate store will only be loaded if the priority store (store 1 for Su 1, store

2 for Su 2) has reached its adjusted maximum temperature (S1MX or S2MX).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Remeha Sol Plus Seite 60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Remeha Sol Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info