Bedienungsanleitung Remington HC4255 (Seite 5 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch, Alle Sprachen)

719577

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

• Use the clipper without any xed combs for trimming hair close to the skin.

• This will trim hair to 1mm, holding the clipper so the blades are perpendicular to the skin will trim hair

to 0.5mm.

TO ATTACH A COMB

• Hook the front edge of the comb to the front teeth of the wide trimmer blade. Then push the back of

the comb down until it snaps in place.

TO REMOVE THE COMB

• Push up the back of the comb until it clicks o the clipper blade.

INSTRUCTIONS FOR CUTTING HAIR

• The QuickCut Clipper’s ergonomic design provides many dierent ways of holding the clipper in use.

• For clipping the top of the head (see g. 1).

• For clipping the back of the head (see g. 2).

• For clipping the sides of the head (see g. 3).

• For detailing (see g. 4).

• For even cutting, allow the comb attachment/blade to cut its way through the hair. Do not force it

through quickly. If you are cutting for the rst time, start with the maximum comb attachment.

• For one all over cut length, attach the desired guide comb and slowly guide the clipper through the

hair against the direction the hair normally grows.

• Remove the guide comb. To produce a clean straight line at the sideburns and the base of the neck,

reverse the hair clipper. Place the reversed clipper at right angles to the head, tips of the blades lightly

touching the skin and then work downwards.

The following instructions are for those users who want dierent trimming lengths on the sides, back and

top of the head

STEP 1  NAPE OF THE NECK

• Set the comb to 3mm or 6mm.

• Hold the clipper with the blade teeth pointing upwards. Begin starting at the centre of the head at the

base of the neck.

• Slowly lift the clipper, working upwards and outwards through the hair, trimming just a little at a time.

STEP 2  BACK OF THE HEAD

• With the comb set at 9mm or 12mm, cut the hair at the back of the head.

STEP 3  SIDE OF THE HEAD

• With the comb set at 3mm or 6mm, trim sideburns. Then change to the longer 9mm guide comb and

continue to cut the top of the head.

STEP 4  TOP OF THE HEAD

• Use the longer length comb attachment and set it to 12mm or 15mm then cut hair on top of the head

against the direction in which the hair normally grows.

STEP 5  THE FINISHING TOUCHES

• Use the clipper without an attachment comb for close trimming around the base and sides of the neck

and around the ears.

• To produce a clean straight line at the sideburns, reverse the hair clipper. Place the reversed clipper at

right angles to the head, tips of the blades lightly touching the skin and then work downwards.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Remington HC4255 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info